SunPower X Series - Page 13

MAXEON SOLAR TECHNOLOGIES, LTD.
Safety and Installation Instructions - Document 001-15497 Rev.AA
©June 2023 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
Mounng Configuraon Diagram
Front View
Back View
Mounng Zone
Locaons
(distance from corner
in mm)
50 - 150
Long Side Mounng,
Point Supported
Long Side Mounng,
Rails Parallel to
Mounng Frame
Short Side Mounng,
Point Supported
(End Mount)
Short Side Mounng,
Rails Parallel to
Mounng Frame
(End Mount)
150 - 296
296 - 536
536 - 825
50 - 150
150 - 296
296 - 536
536 - 825
50 - 150
150 - 296
296 - 536
536 - 825
0 - 350
0 - 350
0 - 350
+2400/-1600
+1800/-1600
+1800/-1600
+1200/-1067
+1200/-1067
+1600/-1067
+2400/-2400
+5400/-2400
+2400/-2400
+1800/-1800
+2400/-2400
+5400/-2400
+2400/-2400
+1800/-1800
+2400/-2400
+5400/-3600
+2400/-2400
+1800/-1800
+1600/-1600
+3600/-1600
+1600/-1600
+1200/-1200
+1600/-1600
+3600/-1600
+1600/-1600
+1200/-1200
+1600/-1600
+3600/-2400
+1600/-1600
+1200/-1200
Mounng Configuraon Diagram
Front View
Back View
Mounng Zone
Locaons
(distance from corner
in mm)
1423mm Holes
Long Side Mounng,
Rails Perpendincular
to Mounng Frame
Long Side Mounng,
Point Supported
1200mm Holes
400mm Holes
+2400/-2400
+2400/-4500
+2400/-4500
+2400/-2400
+5400/-4500
+5400/-4500
+1600/-1600
+1600/-3000
+1600/-3000
+1600/-1600
+3600/-3000
+3600/-3000
1423mm Holes
1200mm Holes
400mm Holes
TOP CLAMPS
BOLTS
GEN 5.6 FRAME PROFILE
A - MLSD Holes
B - Mounng Holes (16X Ø6.8mm)
C - Ground Holes (4X Ø4.2mm)
SunPower Maxeon 6 72 cells Commercial Solar Panel
(SPR-MAX6-XXX-COM)
1039 mm
995 mm
400 mm
1200 mm
1423 mm
1653 mm
2047 mm
0
32 mm
35 mm
32 mm
35 mm
A
B
C
SIDE FRAME PROFILE
END FRAME PROFILE
50
296
536
150
825
0
50
296
536
150
825
0
350
0
350
Test Load 
Downward/Upward
(Pa)
Design Load 
Downward/Upward
(Pa)
Test Load 
Downward/Upward
(Pa)
Design Load 
Downward/Upward
(Pa)
2 Test loads are for informaon purposes only, design loads should be considered for the project design.
4 Rails must not be under the juncon box.
Mounng
Configuraon
Descripon

Mounng
Configuraon
Descripon

Short Side Mounng,
Rails Perpendicular to
Mounng Frame
(End Mount)

Long Side Mounng,
Rails Perpendincular
to Mounng Frame

1 In the cases where hybrid mounng is necessary (combinaon of long and short side mounng), the lowest
design load values should be considered as allowable design load.
3 Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
pares, unless there is a formal authorizaon by Maxeon.
Measurement Tolerances are +/-3 mm for the Length and Width of the Module.
5 Boom Flange Mounng


6 Range indicates posioning of the clamps and not the rails.
