SunStar SPS/A-Pattern Series - Page 167

167
0/1
0/1
0/1
0/1
0~2
0~3
0/1
0/1
0/1
000
Manual moving
Starting position 2nd origin by
manual moving
Returning to the origin 1 after
completing work
Returning when limit error happens
Returning method of starting point
Counting method of the lower
thread counter
Mark of product counter
Time for pattern counter
Trimming in emergency stop during the
operation
001
002
003
004
005
006
007
008
NO. Function name Contents
Explanation and factory-installed setting value Unit
3) Parameter Number Related to General sewing
(Parameter numbers can be different depending on machine type.)
1) DISABLE
 Transfer of the feed plate by using direction keys
1) Disable
2) ENABLE 2) Enable
1) PTRN_STRT_POS 1) Moving the sewing starting position by using direction keys
2) SECND_ORG 2) Setting to the 2nd origin by using direction keys
 Returning to the origin 1 after completing work
1) DISABLE 1) It does not return
2) ENABLE 2) It returns
 If it reaches transfer limit of the feed plate, it returns
1) DISABLE 1) It does not return to the origin of machine
2) ENABLE 2) It returns to the origin of machine
1) SHORTEST 1) Returning through the shortest route
2) ORG_TO_STRT
2) After returning to the original point, return to the starting point
3) REV_ORG_STRT
3) After returning to the origin point by
tracing the pattern shape back
1) UP_COUNT 1) Counting by increasing the sewing completion number
2) DN_COUNT 2) Counting by lowering the sewing completion number
1) DISABLE 1) No use
2) ENABLE 2) Use
1) JOB_SETUP 1) Before completion for sewing preparation
2) JOB_READY 2) After completion for sewing preparation
1) AUTO_TRIM 1) Performing the automatic trimming
2) MANU_TRIM 2) Performing the manual trimming
Main shaft speed acceleration setting
009
User define
1) SLOW_STRT0
2) SLOW_STRT1
3) SLOW_STRT2
4) SLOW_STRT3
5) SLOW_STRT4
6) SLOW_STRT5
7) USER_STRT
200󱈓400󱈓600󱈓800󱈓1000
200󱈓200󱈓400󱈓800󱈓1200󱈓1600
󱈓1800󱈓2000
300󱈓500󱈓700󱈓900󱈓1200
200󱈓200󱈓400󱈓800󱈓1000󱈓1200
󱈓1400󱈓1600
400󱈓500󱈓800󱈓1000󱈓1200
200󱈓200󱈓200󱈓400󱈓600󱈓800
󱈓1000󱈓1200
500󱈓600󱈓900󱈓1100󱈓1300
200󱈓200󱈓400󱈓400󱈓600󱈓800
󱈓1200󱈓1400
500󱈓500
󱈓500󱈓800󱈓1000
200󱈓400󱈓400󱈓600󱈓800󱈓1200
󱈓1600󱈓1800
600󱈓600󱈓600󱈓800󱈓1200
200󱈓400󱈓400󱈓600󱈓800󱈓1200
󱈓1600󱈓2000
A/B-Series
C-Series
A/B-Series
C-Series
A/B-Series
C-Series
A/B-Series
C-Series
A/B-Series
C-Series
A/B-Series
C-Series
1spm
1[100ms]
1
st
needle speed setting
010
200ms
Set the speed for the 1
st
needle.
2~25[100ms]
1[100ms]
2
nd
needle speed setting
011
200ms
Set the speed for the 2
nd
needle.
2~25[100ms]
1[100ms]
3
rd
needle speed setting
012
400ms
Set the speed for the 3
rd
needle.
2~25[100ms]
1[100ms]
4
th
needle speed setting
013
600ms
Set the speed for the 4
th
needle.
2~25[100ms]
3) DESIGN_UP 3) Counting by increasing the sewing completion number by design
4) DESIGN_DN 4)
Counting by lowering the sewing completion number by design