Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 User Manual

Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290

131 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

DE

IMPULS 2.0 Eco R290

IMPULS 2.6 Eco R290

Mobiles lokales Klimagerät

Bedienungsanleitung

Questions and Answers:

J
Joseph BrownAug 14, 2025
Why is my Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 Air Conditioner not cool enough?
- M
  Michelle CannonAug 14, 2025
  There could be several reasons why your Suntec Wellness Air Conditioner isn't cooling effectively: * Doors or windows might be open. Ensure all doors and windows are closed. * Heat sources in the room. If possible, remove any heat sources. * The exhaust hose might not be installed correctly or is blocked. Install the exhaust hose properly and check for any blockages. * The set temperature might be too high. Try resetting the temperature to a lower setting. * The air inlet could be blocked. Clean the air inlet to ensure proper airflow.
C
Cory RobertsAug 17, 2025
What to do if Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 doesn't start when pressing “POWER”?
- M
  Mr. Trevor Shelton IIAug 17, 2025
  If your Suntec Wellness Air Conditioner doesn't start when you press the power button, it could be due to the following reasons: * The water tank might be full, and the “W.F.” light is blinking. Empty the water tank. * The room temperature might be lower than the set temperature during cooling mode. Try resetting the temperature.
C
Crystal MorrisonAug 20, 2025
What does E2 code mean on my Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290?
- K
  Kevin JacksonAug 20, 2025
  The E2 code on your Suntec Wellness Air Conditioner indicates that the water tank is full. You should empty the water tank.
T
Tasha OwensAug 25, 2025
Why is my Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 Air Conditioner so loud?
- S
  Sheri BoydAug 25, 2025
  Your Suntec Wellness Air Conditioner might be loud due to these reasons: * The ground might not be even or flat. Place the unit on an even and flat surface. * The sound might be from the refrigerant flowing inside the unit. This sound is normal.
D
Derrick WolfeAug 27, 2025
What does E0 code mean on my Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290?
- C
  Christopher FrankAug 27, 2025
  The E0 code indicates that the room temperature sensor is not functioning. You should have the sensor replaced. Note that the unit can still operate even without a new sensor.
D
Dean MezaAug 31, 2025
What to do if Suntec Wellness Air Conditioner compressor does not start?
- C
  Cindy KaneAug 31, 2025
  If the compressor of your Suntec Wellness Air Conditioner isn't starting, it might be due to the activation of the thermal protection function. To resolve this, turn off the device and then restart it after waiting for 3 minutes.
R
Russell HendersonSep 2, 2025
Why Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 unit does not start when pressing “POWER”?
- M
  Melissa WilliamsSep 2, 2025
  There are several reasons why your Suntec Wellness Air Conditioner might not start when you press the power button: * If you are in cooling mode, the room temperature might be lower than the set temperature. In this case, reset the temperature. * The ambient temperature could be too low or too high. It is recommended to operate the device at 17-35°C. * In dehumidification mode, the ambient temperature might be too low, it needs to be higher than 17°C. * Doors or windows might be open. Make sure to close all doors and windows. * There might be heat sources in the room. Try to remove any heat sources if possible.
R
Robert IngramSep 6, 2025
What to do if Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 displays E1 Code?
- J
  Julie CarterSep 6, 2025
  If your Suntec Wellness Air Conditioner is showing an E1 code, it indicates that the hose temperature sensor isn't working. In this case, the sensor needs to be replaced.
L
Lisa TurnerSep 9, 2025
What to do if Suntec Wellness Air Conditioner displays E2 Code?
- R
  riggsjasonSep 10, 2025
  If your Suntec Wellness Air Conditioner displays an E2 code, it means the room temperature sensor is not functioning correctly and needs to be replaced.

Suntec Wellness KLIMATRONIC IMPULS 2.6 Eco R290 Specifications

General

Refrigerant	R290
Cooling Capacity	2600 W
Power Supply	220-240 V / 50 Hz
Noise Level (Indoor Unit)	24 dB
Noise Level (Outdoor Unit)	50 dB

Related product manuals

Preview: CLIMATRONIC IMPULS 2.6 Eco R290 APP

CLIMATRONIC IMPULS 2.6 Eco R290 APP

KLIMATRONIC IMPULS 2.6+

Preview: KLIMATRONIC IMPULS 2.0+

KLIMATRONIC IMPULS 2.0+

Klimatronic Transform 7000

Preview: Klimatronic SUMMIT plus 2.7

Klimatronic SUMMIT plus 2.7

Klimatronic Dynamic 8.0 plus

Klimatronic Dynamic 6.0 plus

Preview: KLIMATRONIC EFFECT 7.0 Eco R290

KLIMATRONIC EFFECT 7.0 Eco R290

Preview: KLIMATRONIC Progress plus Series

KLIMATRONIC Progress plus Series

Klimatronic COMFORT 7.0 Eco R290

Preview: Klimatronic CoolFixx 2.0 Eco R290

Klimatronic CoolFixx 2.0 Eco R290

Preview: KLIMATRONIC PROGRESS 7.000 Eco R290

KLIMATRONIC PROGRESS 7.000 Eco R290