EasyManuals Logo

Symmetricom ATS-6511C User Manual

Symmetricom ATS-6511C
115 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #77 background imageLoading...
Page #77 background image
DOC 6511_Release K
ATS-6511A/B/C Users Guide
71
Appendix C Status Port (1900) Example
The data in this first section (boot+) is provided each time the user connects to the status port. It
allows users to obtain all of the system settings/config/status/network parameters each time they
connect to the status port. Once this data is sent the only data forwarded from this port is the data
that has changed since the system has been running. This data will be preceded by the date and
time of the event as this information is updated. It is important to recognize these parameters are
also reflected in the results from the status command.
Network:
If the system time is not set it will show boot + N seconds.
boot+250sec network:broadcast=192.168.0.255
boot+250sec network:default_gateway=192.168.0.254
boot+250sec network:ip=192.168.150.81
boot+250sec network:mode=dhcp
boot+250sec network:netmask=255.255.255.0
If the system time is set (i.e. warmstart) the system will report the actual time the value was set.
2013-08-13-17:58:19.576 network:mode=static
2013-08-13-17:58:19.578 network:static:broadcast=192.168.150.255
2013-08-13-17:58:19.581 network:static:default_gateway=192.168.150.1
2013-08-13-17:58:19.583 network:static:ip=192.168.150.72
2013-08-13-17:58:19.586 network:static:netmask=255.255.255.0
Note: These are the user network settings, if the network:mode = dhcp the actual network
settings for the unit must be obtained using the
status unit:network
command.
ATS-6511B>status unit:network
[MAC] 00:A0:69:00:00:F8
[broadcast] 192.168.150.255
[default_gateway] 192.168.150.1
[ip] 192.168.150.71
[netmask] 255.255.255.0
[OK] 2013-08-13T18:56:32Z
Settings:
If the system time is not set it will show boot + N seconds.
boot+133sec settings:command_port:prompt:enable=1
boot+133sec settings:command_port:prompt:text=ATS-6511A>
boot+133sec settings:diaglog:cpld4370=info
boot+133sec settings:diaglog:fiber=info
boot+133sec settings:diaglog:kas2=info
boot+133sec settings:diaglog:software=info
boot+133sec settings:diaglog:switching=info
boot+133sec settings:diaglog:timecode=info
boot+133sec settings:diaglog:tsc4370=info
boot+133sec settings:diaglog:warmstart=info
boot+133sec settings:fiber:delay:channelA=0.000000000000000e+00
boot+133sec settings:fiber:delay:channelB=0.000000000000000e+00
boot+133sec settings:fiber:delay_diff:channelA=0.000000000000000e+00
boot+133sec settings:fiber:delay_diff:channelB=0.000000000000000e+00
boot+193sec settings:fiber:mode=two_way
boot+133sec settings:fiber:pll:proportional_gain=1.000000000000000e-02
boot+133sec settings:fiber:switching:auto_rearm=1
boot+133sec settings:fiber:switching:master=A

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Symmetricom ATS-6511C and is the answer not in the manual?

Symmetricom ATS-6511C Specifications

General IconGeneral
BrandSymmetricom
ModelATS-6511C
CategoryAmplifier
LanguageEnglish

Related product manuals