Symmons Identity S-6700 User Manual

Identity
™
Model Numbers
S-6700, S-6700TS, S-6701, S-6702
Operation & Maintenance Manual
Specification
Modifications
Note: Append appropriate -sufx to model number.

S-6700
Identity Shower System

S-6700TS
Identity Tub/Shower System

S-6701
Identity Shower System

S-6702
Identity Tub/Shower System
S-6700
Shower system powered by the Temptrol
®
pressure-
balancing valve with integrated volume control. Valve body
includes adjustable stop screw to limit handle turn.
S-6700TS
Tub/shower system powered by the Temptrol
®
pressure-
balancing valve with integrated diverter. Valve body
includes adjustable stop screw to limit handle turn.
S-6701
Shower system powered by the Temptrol
®
pressure-
balancing valve. Features adjustable stop screw to
limit handle turn, integrated volume control, 1 mode
showerhead with easy to clean rubber nozzles and
standard 2.5 gpm (9.5 L/min) ow restrictor.
S-6702
Tub/shower system powered by the Temptrol® pressure-
balancing valve. Features adjustable stop screw to limit
handle turn, integrated diverter, non-diverter tub spout, 1
mode showerhead with easy to clean rubber nozzles and
standard 2.5 gpm (9.5 L/min) ow restrictor.
Components made from metal and nonmetallic materials,
plated in standard polished chrome nish.

-1.5 1.5 gpm (5.7 L/min) flow restrictor

-2.0 2.0 gpm (7.6 L/min) flow restrictor

-143 3 mode showerhead

-145 5 mode showerhead

-231 2 mode showerhead

-CHKS Integral check stops - for use in
installations where a positive shut-off
device is used downstream of mixing valve

-IPS 1/2" female IPS connections

-L/HD
Less showerhead

-LP Loop handle

-LR Lever handle

-OP 13" oval plate

-REB-TRM
Rebuild trim kit

-REV Reverse coring, hot on right, cold on
left, for back to back installations

-SS Slip spout on any tub/shower unit

-STN Satin Nickel finish

-TRM Trim only, valve not included

-X Integral service stops - allows water
shutoff at valve for service
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Compliance
-ASME A112.18.1/CSA B125.1
-WaterSense 1.5 gpm (5.7 L/min)
Certied by
CSA Group
For California Residents
WARNING: This product contains chemicals known to the
State of California to cause cancer, birth defects, or other
reproductive harm.
CG

Symmons Identity S-6700 Specifications

General

Brand	Symmons
Model	Identity S-6700
Category	Kitchen & Bath Fixtures
Language	English

Summary

Symmons Identity Product Overview

Model Number Specifications

Details for Symmons Identity shower and tub/shower system models.

Product Modification Options

List of available modifications and suffixes for Identity series products.

Product Specification Details

Technical specifications for S-6700, S-6700TS, S-6701, and S-6702 models.

Compliance and Standards

Adherence to ASME, CSA, and WaterSense standards.

California Resident Warning

Warning regarding chemicals known to the State of California for health effects.

Product Warranty Terms

Details on Limited Lifetime and 5-Year warranty for residential and commercial use.

Product Dimensions

Dimensional Measurements

Detailed measurements (in inches and mm) for various components of the Identity system.

Shower Valve Hole Size Requirements

Specifies the minimum and maximum diameter for the shower valve hole.

Rough-in and Protrusion Specifications

Details on rough-in dimensions and NPT fitting protrusion from the finished wall.

Parts Breakdown and Tools

Replacement Parts Identification

Itemized list of replaceable parts with corresponding part numbers.

Satin Nickel Finish Note

Instruction to append '-STN' to part numbers for Satin Nickel finish.

Required Installation Tools

List of tools necessary for the installation process.

Installation Guide

Shower Mounting Plate Installation

Steps for installing the shower mounting plate and securing it with screws.

Secondary Handle and Escutcheon Installation

Procedure for attaching the secondary handle and shower escutcheon.

Dome Cover and Handle Installation

Instructions for installing the dome cover and the main handle with set screw.

Tub Spout and Shower Arm Installation

Steps for connecting the tub spout and the shower arm with flange.

Showerhead Installation

Procedure for attaching the showerhead to the shower arm.

Operation and Troubleshooting

Temperature Control Operation

Instructions for adjusting the handle to select cold, warm, or hot water.

Diverter Control Operation

How to operate the diverter handle for tub spout or showerhead.

Volume Control Operation

Instructions for adjusting the volume control for high or low water flow.

Troubleshooting Finish Spotting

Cause and solution for finish spotting due to water supply elements.