Symmons Unity SLW-6612-1.5 User Manual

Unity
®

-0.5 0.5 gpm (1.9 L/min) aerator

-1.0 1.0 gpm (3.8 L/min) aerator

-Delete
Suffix
1.5
2.2 gpm (8.3 L/min) aerator

-STN Satin Nickel finish
Model Numbers
Two Handle Widespread Lavatory Faucet
Operation & Maintenance Manual
SLW-6612-1.5, SLW-6610-1.5
Two handle widespread lavatory faucet featuring an 8” to
16” mounting conguration. Includes ceramic cartridges,
1/4” copper supply lines, 1/2” IPS inlet connections, 50/50
drain assembly and standard 1.5 gpm (5.7 L/min) aerator.
Components made from brass and nonmetallic materials
plated in standard polished chrome nish.
Specification
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Dimensions
Note: Dimensions subject to change without notice.
Modifications
Note: Append appropriate -sufx to model number.
CG
CG

SLW-6612-1.5
Unity Two Handle Widespread Lavatory Faucet

SLW-6610-1.5
Unity Two Handle Widespread Lavatory Faucet
Less Rod & 50/50 Drain Assembly
Measurements
A 8”, 203 mm
B 5”, 127 mm
C 3 3/16”, 81 mm
D
Deck Thickness Ref.
Max. 1 3/8”, 35 mm
E
Hole Size
Min. Ø 1 3/8”, 35 mm
Max. Ø 1 5/8”, 41 mm
F
(2x) Hole Size
Min. Ø 1 1/4”, 32 mm
Max. Ø 1 1/2”, 38 mm
G 3 15/16”, 100 mm
H 5 1/16”, 129 mm
I Min. 2”, 51 mm
J 1/2-14 NPSM
AA
C
BB
D
EE
FF
G
H
I
J
Compliance
Certied by
CSA Group
-NSF/ANSI 372, NSF/ANSI 61.9
-ASME A112.18.1/CSA B125.1
-WaterSense 1.5 gpm (5.7 L/min)
WARNING: This product can expose you to chemicals
including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov.

Symmons Unity SLW-6612-1.5 Specifications

General

Brand	Symmons
Model	Unity SLW-6612-1.5
Category	Kitchen & Bath Fixtures
Language	English

Summary

Specification

Warranty Information

California Proposition 65 Warning

Dimensions

Parts Breakdown

Tools Required

Installation Steps

Remove Valve Body Hardware

Remove washer (P), nut (Q), and screws (R) from valve body (M).

Insert Valve Bodies

Insert valve bodies (M) through sink holes.

Secure Valve Body Assembly

Install washer (P), nut (Q), and screws (R) to valve body (M) to secure assembly under deck surface.

Seal Escutcheon

Turn escutcheon (D) clockwise to seal to deck surface.

Secure Spout

Install gasket (L), washer (N), and nut (O) to spout (F) to secure assembly under deck surface.

Install Drain Assembly

Seat flange (S4) into sink, install gasket (S6), washer (S9), nut (S10), screw on tail piece (S11) and hand tighten.

Install Tail Piece and Stopper

Turn tail piece (S11) and flange (S4) so pivot faces faucet. Pull assembly into drain hole. Secure hardware and install stopper (S1).

Additional Installation Steps

Attach Pivot Rod Hardware

Attach sealing washer (S12), pivot rod (S13), and cup washer (S14) to tailpiece (S11). Hand tighten nut (S7).

Connect Lift Rod

Connect lift rod (A) to clevis strap (S2) with thumb screw (S3). Insert pivot rod (S13) into clevis strap (S2).

Connect Hoses and Flush Lines

Connect hoses (T) and supply lines. Remove aerator (J), flush lines, and check for leaks.

Maintenance Procedures

Disassemble Handle

Remove set screw (B). Turn counter-clockwise to disassemble handle (C) and nut (G) from cartridge (H or I).

Remove Cartridge

Remove cartridge (H or I) from valve body (M). Inspect for debris; replace if necessary.

Reassemble Handle and Cartridge

Install cartridge and handle assembly following steps 1 and 2 in reverse.

Troubleshooting

Water Staining on Finish

Water supply may cause staining. Clean trim with soft cloth, mild soap/water or non-abrasive cleaner.