What to do if my T.I.P. Lighting Equipment pump stops after a short time?
If your T.I.P. Lighting Equipment pump stops shortly after starting due to the thermal motor protection, verify that the electrical supply matches the type plate information using a GS-compliant device. Also, remove any blockages from the pump or intake openings. Ensure the liquid temperature isn't too high and eliminate any causes of the pump running dry.
What to do if my T.I.P. Lighting Equipment motor is running but not pumping water?
If your T.I.P. Lighting Equipment pump isn't discharging liquid and the motor is running, first, make sure the pump housing is filled with liquid by ensuring the water level in the pool is above the pump's suction point and the strainer is free of dirt. Then, check for air leaks by ensuring intake line connections are tight and that there are no siphons, kinks, counter-slopes, or narrow spots in the intake lines. Finally, inspect the check valve for blockages or damage and clean the pump insert, checking the impeller for blockages.
How to fix a noisy T.I.P. Lighting Equipment pump?
If there is noise in the T.I.P. Lighting Equipment pump during operation, check and clean the suction hose for any blockage during aspiration. Improve the suction inlet by ensuring it is under the water level of the swimming pool, reduce the number of screws, and assemble a pipe with a larger diameter. If air penetrates the intake line, refer to section 2 of this table. For defect bearings or faults in the impeller, contact your local service partner or the manufacturer.
What to do if the T.I.P. Swimming Pool Filter motor is running, but no liquid is being discharged?
If your T.I.P. Swimming Pool Filter pump isn't discharging liquid but the motor is running, it could be due to a few reasons. First, ensure the pump housing is filled with liquid by checking that the water level in your pool is above the pump's suction point and that the strainer is free of dirt. Another cause might be air entering the pump body. Inspect the connection points of the intake line to ensure they are tight. Also, verify that the inlet opening of the intake line, including the check valve, is submerged in the liquid. Confirm the check valve is tight and not jammed. Finally, make sure there are no siphons, kinks, counter-slopes, or narrow spots along the intake lines.
Why is my T.I.P. Swimming Pool Filter not pumping water and the motor isn't running?
If your T.I.P. Swimming Pool Filter pump isn't discharging liquid and the motor isn't running, several issues could be at play. First, check for voltage using a device complying with GS standards, ensuring you observe all safety information and verify the plug is correctly positioned. It's possible that the thermal motor protection has been triggered, so disconnect the pump, let it cool down, and identify the cause. A blocked pump wheel could also be the culprit, so remove any obstructions. If these steps don't resolve the issue, the capacitor or floating switch might be defective, and you should contact customer service.
Why does my T.I.P. Swimming Pool Filter stop after a short time?
If your T.I.P. Swimming Pool Filter stops shortly after starting due to the thermal motor protection feature activating, several factors could be responsible. Make sure the electrical supply matches the information on the type plate, using a GS-compliant device to check the voltage. Remove any blockages from the pump or intake openings. Ensure the liquid temperature doesn't exceed the maximum admissible value. Also, address any causes of the pump running dry.
How to reduce noise in T.I.P. Swimming Pool Filter during operation?
If you notice noise in the T.I.P. Swimming Pool Filter pump during operation, there could be several reasons. A defect bearing or Störung im Flügelrad can cause noise, so contact your local service partner or the manufacturer. Air entering the intake line can also be a cause, refer to section 2 of this table. Blockade beim Ansaugen can also cause noise, so check and clean the suction hose. Störung beim Saugen can also cause noise, so improve the suction inlet by ensuring it is below the water level, reduce the number of screws, and assemble a pipe with a larger diameter.
What to do if T.I.P. Swimming Pool Filter has low current?
Low current in your T.I.P. Swimming Pool Filter can often be attributed to a dirty filter. Try rinsing or cleaning the filter. Additionally, check the filter basket of the sand filter for dirt and clean it if necessary. A blockage in the pipe could also be the cause; inspect the pipes, avoid bending the hoses, and flush with sufficient water if needed.
Instructions for the safe and correct setup of the device, covering placement and environmental conditions.
Steps for assembling the sand filter tank, including mounting the pump and filling with sand.
Guidance on connecting the inlet and outlet hoses, emphasizing proper diameter and placement for efficient operation.
Guidelines for permanently installing the pump, focusing on electrical connection accessibility and surface stability.
General| Brand | T.I.P. |
|---|---|
| Model | SPF 180 |
| Category | Swimming Pool Filter |
| Language | English |
To Next Page
