Tar River EMF - Page 23

Flail Mower
EFGC
23
No
Part Number
Description
Office Use Only
QTY
1
EGC101L
3 Point Hitch– Left
26.001.036
1
EGC101R
3 Point Hitch– Right
26.001.036
1
2
EGC102
Hitch Pin– Upper
03.31.03.040
1
3
EGC103
Hitch Bushing– Upper
21.084.059
1
4
LYNPN10
Lynch Pin– M10
03.35.008
3
5
BM162090
Bolt– M16 x 2.0 x 90
03.180.01.027
2
6 EGC106 Hitch Bushing- Upper
21.084.058
2
7
LNM1620
Locking Nut– M16 x 2.0
03.14.006
30
9
EGC109
Hitch Bushing Lower- (Cat 2)
21.002.011
2
10
EGC110
Hitch Bushing– Lower
03.31.01.041
2
11
BM1217535
Bolt– M12 x 1.75 x 35
03.18.01.013
12
12
LNM12175
Nut– M12 x 1.75
03.14.004
28
13
EGC113-115
Shaft– Protection Plate for EFGC115
21.077.012
1
EGC113-135 Shaft– Protection Plate for EFGC135
21.077.010
1
EGC113-155
Shaft– Protection Plate for EFGC155
21.077.008
1
EGC113-175
Shaft– Protection Plate for EFGC175
21.077.009
1
EGC113-195
Shaft– Protection Plate for EFGC195
21.077.011
1
14
BCM106A
Protection Plate– M72 x 2
54.18.037.007
N
BCM106B
Protection Plate– M72 x 2 w/Gap
54.18.037.009
N
BCM106C
Protection Plate– M51 x 2
54.18.037.010
N
BCM106D
Protection Plate– M43 x 2
54.18.037.011
N
15
CP4x25
Cotter Pin– M4 x 25
03.36.018
2
16
EGC116-115
Safety Bar– Front for EFGC115
26.026.038
1
EGC116-135
Safety Bar– Front for EFGC135
26.026.033
1
EGC116-155
Safety Bar– Front for EFGC155
26.026.024
1
EGC116-175
Safety Bar– Front for EFGC175
26.026.029 1
EGC116-195
Safety Bar– Front for EFGC195
26.026.034
1
17
LNM08125
Self-locking Nut– M8 x 1.25
03.14.002
6
18
BM0812520
Bolt– M8 x 1.25 x 20
03.18.01.032
16
19
EGC119
Counter Knife
26.065.011
6
20
FW10
Flat Washer– M10
03.04.003
12
21
LW10
Lock Washer– M10
03.09.01.003
12
22
BM101525
Bolt– M10 x 1.5 x 25 (Full thread)
03.18.01.003
16
23
KM100830
Key– M10 x 8 x 30
03.13.006
1
24
BCM112
800 gr Forging Hammer (Galv)
24.99.001
28
25
BM162085
Bolt– M16 x 2.0 x 85
03.18.01.192
28
26
EGC126-115
Rotor Shaft for EFGC115
26.005.149
1