9C-299C-29TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
taken.taken. wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.
7711..0000 SS//AA OOuuttppuut t 1 1 ((wwiirrees As A0044
& A05) related fault:& A05) related fault:
– wires A04 & – wires A04 & A05A05
configured as analogconfigured as analog
output:output:
output wires areoutput wires are
shorted to eachshorted to each
otherother, or , or the sensethe sense
line is shorted to bat-line is shorted to bat-
tery +, or the plustery +, or the plus
line is shorted toline is shorted to
ground.ground.
– wire A04 con– wire A04 config-fig-
ured as digital out-ured as digital out-
put:put:
the output is shortedthe output is shorted
to ground.to ground.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
– wires A04 & – wires A04 & A05A05
configured as analogconfigured as analog
output:output:
output wires areoutput wires are
shorted to eachshorted to each
other, or the senseother, or the sense
line is shorted to bat-line is shorted to bat-
tery +, or the plustery +, or the plus
line is shorted toline is shorted to
ground.ground.
– wire A04 co– wire A04 config-nfig-
ured as digital out-ured as digital out-
put: the output isput: the output is
shorted to ground.shorted to ground.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid: solenoid: Check Check thethe
wiring between thewiring between the
controller and thecontroller and the
VFS/SelectVFS/Selector or sole-sole-
noid 1, Check thenoid 1, Check the
VFS/selector sole-VFS/selector sole-
noid 1.noid 1.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.
7711..0011 SS//AA OOuuttppuut t 1 1 ((wwiirrees As A0044
& A05) related fault:& A05) related fault:
– wires A04 & – wires A04 & A05A05
configured as analogconfigured as analog
output:output:
the output wire is notthe output wire is not
connected, or itsconnected, or its
plus line is shorted toplus line is shorted to
battery +.battery +.
– wire A04 con– wire A04 config-fig-
ured as digital out-ured as digital out-
put:put:
the output is shortedthe output is shorted
to battery +, or theto battery +, or the
output is not con-output is not con-
nected.nected.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
– wires A04 & – wires A04 & A05A05
configured as analogconfigured as analog
output:output:
the output wire is notthe output wire is not
connected, or itsconnected, or its
plus line is shorted toplus line is shorted to
battery +.battery +.
– wire A04 co– wire A04 config-nfig-
ured as digital out-ured as digital out-
put:put:
the output is shortedthe output is shorted
to battery +.to battery +.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the VFS/ler and the VFS/
Selector solenoid 1,Selector solenoid 1,
Check the VFS/Check the VFS/
selector solenoid 1.selector solenoid 1.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.
FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
7711..0022 SS//AA OOuuttppuut t 1 1 ((wwiirrees s AA0044
& A05) related fault:& A05) related fault:
– wires A04 & – wires A04 & A05A05
configured as analogconfigured as analog
output:output:
the output currentthe output current
exceeds 1400 mA.exceeds 1400 mA.
Action will depAction will dependend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical ou– critical output (eg.tput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
kk
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
– wires A04 & – wires A04 & A05A05
configured as analogconfigured as analog
output:output:
the output currentthe output current
exceeds 1400 mA.exceeds 1400 mA.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the VFS/ler and the VFS/
Selector solenoid 1,Selector solenoid 1,
Check the VFS/Check the VFS/
selector solenoid 1.selector solenoid 1.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
i i b hi i b h
To Next Page
Loading...
