9C-359C-35TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
e ou pu s s o ede ou pu s s o ed
to battery +, or theto battery +, or the
output is not con-output is not con-
nected.nected.
o ac o s beo ac o s be
taken.taken.
g be ee eg be ee e
controller and thecontroller and the
other device, Checkother device, Check
the other device.”the other device.”
7755..0022 SS//AA OOuuttppuut 5 t 5 ((wwiirre Be B0033))
related fault:related fault:
– wire B03 con– wire B03 config-fig-
ured as analog out-ured as analog out-
put:put:
the output currentthe output current
exceeds 1400 mA.exceeds 1400 mA.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
– wire B03 co– wire B03 config-nfig-
ured as analog out-ured as analog out-
put:put:
the output currentthe output current
exceeds 1400 mA.exceeds 1400 mA.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid: Check thesolenoid: Check the
wiring between thewiring between the
controller and thecontroller and the
Selector solenoid 4,Selector solenoid 4,
Check the selectorCheck the selector
solenoid 4.solenoid 4.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.”the other device.”
7755..0033 SS//AA OOuuttppuut 5 t 5 ((wwiirre Be B0033))
related fault:related fault:
– wire B03 con– wire B03 config-fig-
ured as analog out-ured as analog out-
put:put:
the output current isthe output current is
out of range, occursout of range, occurs
when the load haswhen the load has
the incorrect imped-the incorrect imped-
ance.ance.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
– wire B03 co– wire B03 config-nfig-
ured as analog out-ured as analog out-
put: the output cur-put: the output cur-
rent is out of range,rent is out of range,
occurs when theoccurs when the
load has the incor-load has the incor-
rect impedance.rect impedance.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid: Check thesolenoid: Check the
wiring between thewiring between the
controller and thecontroller and the
Selector solenoid 4,Selector solenoid 4,
Check the selectorCheck the selector
solenoid 4.solenoid 4.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.”the other device.”
FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
7766..0000 SS//AA OOuuttppuut t 6 (6 (wwiirre Be B0055))
related fault:related fault:
– wire B05 conf– wire B05 config-ig-
ured as analog/digi-ured as analog/digi-
tal output:tal output:
output wire isoutput wire is
shorted to ground.shorted to ground.
Action will depAction will dependend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical ou– critical output (eg.tput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
– wire B05 con– wire B05 config-fig-
ured as analog/digi-ured as analog/digi-
tal output:tal output:
output wire isoutput wire is
shorted to ground.shorted to ground.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the Selectorler and the Selector
solenoid 6, Checksolenoid 6, Check
the selector solenoidthe selector solenoid
6.6.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
To Next Page
Loading...
