TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
1-141-14
PPrroobblleemm CCaauussee CCoorrrreeccttiioonn
1.1. EnEngigine wne wilill nl notot
crank or crankscrank or cranks
slowlyslowly
1.1. BatBattertery diy discsconneonnect sct swiwitch itch is turs turnedned
off.off.
2.2. EngEngine ine dridrive ve uniunits ts are are engaengagedged..
3.3. BatBattertery cy connonnectectionions ars are be brokroken,en,
loose or corroded.loose or corroded.
4.4. LoLow w babatttterery y chchararge.ge.
5.5. BatBattertery ry ratiating ng is is too too lowlow..
6.6. Oil Oil for for operoperatiating cng condonditiitions ons isis
incorrect.incorrect.
7.7. OiOil ll levevel el is is totoo ho higigh.h.
8.8. Oil Oil temtemperperatuature re is is too too lowlow..
9.9. EleElectrctric sic shifhifter iter is not s not in thin the neue neutratrall
position.position.
10.10. CircuCircuit breaker (CBit breaker (CB13, CB14,13, CB14,
CB15, CB27, CB28 or ECM 30CB15, CB27, CB28 or ECM 30
amp; Illustrations 1-6 and 6-6 thruamp; Illustrations 1-6 and 6-6 thru
6-8) is tripped or defective.6-8) is tripped or defective.
1111.. DefecDefective accesstive accessory power sole-ory power sole-
noid (L1).noid (L1).
12.12. Defective Defective neutral start neutral start relay (K9,relay (K9,
Illustration 6-6).Illustration 6-6).
13.13. Defective Defective start assist start assist solenoid (L2).solenoid (L2).
14.14. DefecDefective startertive starter..
15.15. DefecDefective ignititive ignition switch (S1).on switch (S1).
16.16. Blown fuBlown fuse (5 amp) to tse (5 amp) to the ECM.he ECM.
17.17. Loose or brLoose or broken wiroken wires / plugs /es / plugs /
pins between any of the compo-pins between any of the compo-
nents in Causes 9. thru 16. of thisnents in Causes 9. thru 16. of this
Problem.Problem.
18.18. The TICS emergThe TICS emergency hydraency hydrauliculic
movement stop has beenmovement stop has been
depressed to disable certaindepressed to disable certain
functions.functions.
1.1. TTurn baurn battettery diry discosconnennect swct switcitch on.h on.
2.2. DisDisengengage age engengine ine dridriven ven uniunits.ts.
3.3. CheCheck ck for for damdamageage. . RepReplaclace, e, tigtight-ht-
en or clean.en or clean.
4.4. CheCheck elck electectrolrolyte lyte leveevel and sl and specpecifiificc
gravity. gravity. Recharge or Recharge or replace bat-replace bat-
teries.teries.
5.5. RepReplaclace with ce with corrorrect rect rateated battd batteryery..
6.6. ChaChange nge oil oil and and filfilterter. . RefRefer er to to thethe
Fuel and Lubricant Specifica-Fuel and Lubricant Specifica-
tionstions in thein the AppendicesAppendicesfor thefor the
proper type of oil to be used.proper type of oil to be used.
7.7. CheCheck ck the the oil oil levlevel. el. VVerierify fy the the oiloil
pan capacity. pan capacity. Drain excess Drain excess oil ifoil if
necessary. necessary. Fill the Fill the system to system to thethe
specified level.specified level.
8.8. InInststalall oil oil pal pan hen heataterer..
9.9. PlaPlace elce electectric ric shishiftefter in thr in the neue neutratrall
position.position.
10.10. Reset or Reset or replace circuit replace circuit breaker(s).breaker(s).
11.11. Replace acReplace accessory cessory power power solenoidsolenoid
(L1).(L1).
12.12. Replace neutral Replace neutral start relay start relay (K9).(K9).
13.13. Replace start Replace start assist solenoid assist solenoid (L2).(L2).
14.14. Replace or Replace or repair starterrepair starter..
15.15. Refer to ComRefer to Component 4. of theponent 4. of the
Component TroubleshootingComponent Troubleshooting
chart inchart in Section 6.Section 6.
16.16. ReplacReplace fusee fuse(s).(s).
17.17. IsolaIsolate and repairte and repair..
18.18. Pull the TICS emergPull the TICS emergency hydrency hydraulicaulic
stop to its Out position.stop to its Out position.
To Next Page
Loading...
