Technics Quartz SL-10 - Specifications

Button pressed
Cueing up/down
Cueing up (¥)
Cueing down (¥)
Pressed momentarily
(less than one second)
Tonearm moves inward
in approx. 1mm
steps.
Pressed intermittently
Quick Reference Chart for Start and
Stop Button Operation
Start Button
Pressed continuously
Lightly
Tonearm moves
inward
Tonearm rises and
Tonearm rises
returns to start position
and begins play again
Specifications
@ General
Power supply:
Power consumption:
Dimensions:
(WXH*D)
Weight:
@ Turntable section
Type:
Drive method:
Motor:
Drive control method:
Turntable platter:
Turntable speeds:
Speed deviation:
Wow and flutter:
~110-120/220-240V. 50 Hz or 60 Hz
DC 12V (DC input jack)
20 W (AC)
6 W (DC)
31.5 X 8.8 * 31.5 cm
(12-1/2" »& 3-1/2" % 12-1/2")
6.5 kg (14.3 Ib.)
Quartz direct drive
Automatic turntable
Auto start/Auto lead-in
Auto return
Auto stop
Repeat play
Auto speed select
Auto size select
2-speed search functions
Record presence detection
Direct drive
Brushless DC motor
Quartz-phase-locked control
Aluminum die-cast
Diameter 30 cm (12 inches)
33-1/3 rpm and 45 rpm
Auto speed select
(Manual selection possible)
Within =0.002%
0.012% WRMS’
0.025% WRMS (JIS C5521)
= 0.035% peak
(IEC 98A Weighted)
Measured by obtaining signal from built-in frequency.
| generator of motor assembly.
UN =
Rumble:
—56 dB (IEC 98A Unweighted)
~78 dB (IEC 98A Weighted)
and moves
inward,
@ Tonearm section
Type:
Effective length:
Tracking error angle:
Effective mass:
Resonance frequency:
Tonearm drive motor:
@ Cartridge section
Type:
Cantilever:
Damper:
Frequency response:
Output voltage:
Channel separation:
Channel balance:
DC resistance:
Impedance:
Compliance (dynamic):
Vertical tracking angle:
Stylus pressure range:
Stylus tip:
Effective mass:
Weight:
Replacement cartridge:
Pressed momentarily
(less than one second)
Moves faster.
Tonearm rises
and moves
faster
Auto-return (reject)
Dynamic balanced type
Linear tracking tonearm
4-pivot gimbal suspension
105 mm (4-1/8")
Within =0.1°
9g (including cartridge)
12 Hz
Coreless OC motor
Moving coil stereo cartridge
Coreless twin-ring coil type
Pure boron pipe
TTDD (Technics Temperature
Defense Damper)
10 Hz to 60 kHz
10 Hz to 10 KHz =0.5 dB
0.2 mV at 1 kHz,
5 cm/s. zero to peak lateral
velocity
(0.56 mV at 1 KHz, 10cm/s. zeroto
peak 45° velocity [DIN 45 500))
More than 25 dB at 1 KHz
More than 20 dB at 10 kHz
Within 1 dB at 1 kHz
302
30 Pure resistance
12 < 10“ em/dyne at 100 Hz
20°
1.25 +0.25 g (12.5 +2.5mN)
0.2 X 0.7 mil (5 * 18um)
Elliptical stylus
Block diamond tip
0.23 mg
6.0 g (cartridge only)
EPS-310MC
—10—
Stop Button
Pressed continuously
Pressed intermittently
Tonearm moves.
outward in approx.
1 mm steps.
Lightly
re
Tonearm moves
Moves faster.
outward.
Tonearm rises
and moves
faster
Tonearm rises
and moves
outward.
@ MC pre-preamp section
Rumble: —70 dB (IHF A)
Frequency response: 20 Hz to 20 kHz +0.5 dB
Output level: 2.5 mV
Overall distortion: 0.02% (connected to Technics
SU-70AIl)
@ Circuit components
MIChOPTOGRSSON iii ice cine sata a seca eines beeen Shae 1
WG 260644 paeek Riad ence tiaeAwa hae ealed hwiptesietess 8
Quartz crystal OSCIlatOr 2.0... eee eee eee ees 1
Phototransistors:.. 6 ices acca nee cd ee the ee cies 5
COG 552 2 hes aie it’ tte wale 8 tre istaracgcoereajen amiteiale siaveles.« 18
THANSISIOLS f crc.sisie'e eles eels ere tiecw ba Fara saergip be MO wees eel 0'5 8 33
DION OSs. iad Aiwsaes sleet anaes anaes vues 24
@ Accessories supplied:
Stylus cleaning brush. ......... ccc eee eee ee eee eee 1
Optical sensor light-block sheets ...............0 0c cee 2
Screwdriver
Specifications subject to change without notice.
Weight and dimensions shown are approximate.