Technics SX-PR270 M User Manual

a
SYMPTOMS
WHICH
APPEAR
TO
BE
SIGNS
OF
TROUBLE
ee
Se
The
following
changes
in
performance
may
occur
in
the
Technics
Digital
Ensemble
but
do
NOT
indicate
trouble.
Phenomenon
Remedy
Sounds and effects
)The
buttons,
keys,
etc.
malfunction.
e Turn off the POWER button once, then turn it on again. If this
procedure is not successful, turn off the POWER button once.
Then, while pressing the three leftmost buttons in the
RHYTHM SELECT section (METRONOME 1, METRONOME
2 and 1) at the same time, turn the POWER button on again.
(Note that, in this case, all programmable settings, functions
and memories return to their factory-preset status.)
No
sound
is
produced
when
the
keys
are
pressed.
eThe MAIN VOLUME is at the minimum setting: Adjust the
volume with the MAIN VOLUME control.
eThe BALANCE volumes are set to OFF. Use the sliding
BALANCE controls to set the volumes of the relevant parts to
appropriate levels.
e The local control for a part performed on the keyboard is set
to off. Set the local control to on.
The
octave
is
higher
or
lower
for
some
SOUND
SELECT
sounds.
e An octave change is programmed for some instrument sounds
in order to make them easy to play. This is not a malfunction.
|
Only
percussive
instrument
sounds
are
produced
when
the
keyboard
is
played.
e The KEYBOARD PERCUSSION button is on. Turn it off to
return the keyboard to the normal sound.
[Faspae i De ee
The
sustain
does
not
work
even
when
the
sustain pedal is depressed.
eWhen the SUSTAIN PEDAL button is off, the sustain does
not work even when the pedal is depressed. Turn on the
SUSTAIN PEDAL button.
The
sostenuto
pedal
and
soft
pedal
do
not
operate
properly.
For
example,
when
the
soft
pedal
is
depressed,
the
rhythm
starts
or
a
fill-in
is
played.
e Different functions can be programmed in these pedals. You
can return the pedals to their original functions by turning off
the instrument once, or by using the PEDAL SETTING mode.
Rhythm
The rhythm does not start.
Use the sliding BALANCE control to set the DRUMS volume
to an appropriate level.
ein the RHYTHM SELECT section, a COMPOSER number
button with no stored performance was selected. Change the
rhythm or store a new rhythm pattern in the COMPOSER.
eWhen
a
SEQUENCER
part
button
(in
the
PROGRAM
SECTION)
is
on,
the
rhythm
will
not
start
unless
the
rhythm
has
been
stored.
Turn
off
the
SEQUENCER
part
buttons.
e The MIDI clock is set to the external clock. Set the MIDI clock
to the internal clock.
ee DRUMS volume in the BALANCE section is set to OFF.
AUTO PLAY CHORD
No
sound
is
produced
for
the
automatic
accompaniment,
or
only
the
sounds
of
some
parts
are
produced.
eThe
BALANCE
volumes
are
set
to
OFF.
Use
the
sliding
BALANCE
controls
to
set
the
volumes
of
the
relevant
parts
to
appropriate
levels.
eAn
ACCOMP
part
does
not
sound
if
its
corresponding
ACCOMP
PART
1,
2
or
3
button
is
off.
Press
the
desired
ACCOMP
PART
1,
2
and
3
buttons
to
turn
them
on.
e
An
ACCOMP
part
does
not
sound
if
its
volume
is
set
toO.
The
volume
of
each
ACCOMP
part
can
be
adjusted
independently.

Technics SX-PR270 M Specifications

General

Brand	Technics
Model	SX-PR270 M
Category	Musical Instrument
Language	English