Tektronix DPO70804C User Manual

x
MSO70000C/DX Series Mixed Signal Oscilloscopes
DPO70000C/DX Series Digital Phosphor Oscilloscopes
DPO7000C Series Digital Phosphor Oscilloscopes
MSO5000B and DPO5000B Series Oscilloscopes
ZZZ
User Manual
*P071298004*
071-2980-04

Tektronix DPO70804C Specifications

General

Bandwidth	8 GHz
Channels	4
Vertical Resolution	8 bits
Vertical Sensitivity	1 mV/div to 1 V/div
Input Impedance	50 Ω or 1 MΩ
Input Coupling	DC, AC, GND
Maximum Input Voltage	5 Vrms (50 Ω), 400 V (1 MΩ)
Trigger Modes	Edge, Runt, Setup/Hold, Serial
Display	12.1-inch XGA color LCD
Interface	LAN, USB, GPIB, HDMI
Operating Temperature	0 °C to 50 °C
Timebase Accuracy	±5 ppm

Summary

Important safety information

General safety summary

Review safety precautions to avoid injury and prevent damage to the product or connected products. Comply with codes.

Service safety summary

Additional information for safely performing service. Only qualified personnel should perform service.

Compliance information

EMC compliance

Details the EMC (electromagnetic compliance) standards the instrument complies with.

Safety compliance

Lists the safety standards with which the product complies.

Preface

Key features

Highlights the main capabilities and specifications of the MSO/DPO70000/7000/5000B Series instruments.

Install your instrument

Standard accessories

Operating requirements

Specifies the environmental and operational requirements for the instrument.

Preventing ESD

Provides techniques to prevent electrostatic discharge damage to the instrument input.

Operating system restore

Getting acquainted with your instrument

Front panel

Identifies the components and controls located on the front panel of the instrument.

Side and rear panels

Locates and identifies the connectors and ports on the side and rear panels.

Interface and display

Control panel

Describes the function of each control on the instrument's front panel.

Inspect your instrument

Verify internal diagnostics pass

Procedure to verify the instrument's functionality using internal diagnostics.

Acquisition

Signal path compensation

Procedure to perform signal path compensation for accurate measurements.

Setting up analog signal input

Guides on connecting probes and selecting input channels for signal acquisition.

Using Autoset

Procedure to automatically set up the instrument for signal acquisition.

Probe compensation and deskew

Guidance on optimizing measurement accuracy by compensating and deskewing probes.

Acquisition concepts

Changing the acquisition mode

Using FastAcq

How to use FastAcq mode to capture transient events and display phenomena.

Using DSP enhanced bandwidth

Utilizes DSP for accurate rise time measurements and extended bandwidth.

Setting up digital signal input

Guides on connecting logic probes and setting up digital channels for signal acquisition.

Setting up digital channels

Details on setting digital channel threshold, size, position, and label.

Setting up a bus

Procedure to set up serial and parallel buses for triggering and display.

Set up a serial bus

Configuration steps for setting up serial bus parameters.

Set up a parallel bus

Configuration steps for setting up parallel bus parameters.

Setting up Action on Event

Configure the instrument to save files or send emails when specific events occur.

Sending E-Mail on Trigger

Procedure to configure and enable email notifications triggered by events.

Setting up E-Mail on Event

Details for setting up recipient addresses, SMTP server, and attachments for email alerts.

Using horizontal delay

Display a waveform

Using MultiView Zoom

How to magnify waveforms vertically, horizontally, or in both dimensions.

Zooming in multiple areas

Using Wave Inspector to manage long record length waveforms

How to use Wave Inspector controls for efficient work with long record length waveforms.

Searching and marking waveforms

How to mark locations of interest in acquired waveforms for analysis.

To automatically set and clear (delete) search marks

Using a visual search

Analyzing waveforms

Taking automatic measurements

Procedure to select channels and measurements for automatic analysis.

Customizing an automatic measurement

Taking cursor measurements

Use cursors to take manual measurements on acquired waveform data.

Setting up a histogram

How to display vertical or horizontal histograms for statistical analysis.

Using math waveforms

Using Spectral Analysis

Using the Serial Error Detector

Procedure to use the Serial Error Detector for Bit, Frame, Symbol, and Character tests.

Using mask testing

How to compare a signal to a predefined template or mask.

Using limit testing

How to compare an active signal with a template waveform for pass/fail testing.

MyScope

Creating a new MyScope control window

Steps to create custom control windows with regularly used controls.

Using MyScope control windows

To edit a MyScope control window

Saving and recalling information

Saving screen captures

Saving waveforms

Saving instrument setups

Saving measurements

Application examples

Capturing intermittent anomalies

Example of using FastAcq to find and capture intermittent anomalies in signals.

Triggering on buses

Procedure for setting up bus triggers on various serial and parallel buses.

Triggering on a video signal

Triggering on lines

Correlating data between a Tektronix oscilloscope and logic analyzer

Appendix D

P6616 General-Purpose Logic Probe instructions

Connecting the probe to your circuit

Setting up the probe

Functional check

Safety summary

Summarizes safety precautions for using the probe.