Tektronix MSO2024B Programmer's Manual

Command Groups
Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:ADDRess:MODe
Sets or returns the I2C address mode to 7
or 10-bit
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:ADDRess:TYPe
Sets or returns the I2C address type to I2C
special addresses
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:ADDRess:VALue
Sets or returns the binary address string to
be used for I2C search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:CONDition
Sets or returns the search condition for I2C
search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:DATa:DIRection
Sets or returns the I2C search condition to
be valid on a R EAD, WRITE or either
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:DATa:SIZe
Sets or returns the length of the data string
in bytes to be used for I2C search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:I2C:DATa:VALue
Sets o r returns the binary data string to be
used for I2C search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:PARallel:VALue
Sets o r returns the binary data string to be
used for a parallel trigger search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:RS232C:CONDition
Sets or returns the trigger condition for a
RS232 trigger
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:RS232C:RX:DATa:SIZe
Sets or returns the length of the data string
for a RS232 trigger, if the trigger condition
is RX
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:RS232C:RX:DATa:VALue
Sets or returns the binary data string for a
RS232 trigger, if the condition involves RX
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:RS232C:TX:DATa:SIZe
Sets or returns the length of the data string
to be used for a RS232 Trigger, if the Trigger
condition is TX
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:RS232C:TX:DATa:VALue
Sets o r returns the binary data string to be
used for a RS232 trigger, if the condition
involves RX
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:SPI:CONDition
Sets or returns the s earch condition for SPI
search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:SPI:DATa{:MISO|:IN}:VALue
Sets o r returns the binary data string to be
used for SPI search if the search condition is
MISO or MISOMOSI.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:SPI:DATa{:MOSI|:OUT}:VALue
Sets or returns the binary data string for an
SPI search if the search condition is MISO or
MISOMOSI
SEARCH:SEARCH<x>:TRIGger:A:BUS:
B<x>:SPI:DATa:SIZe
Sets or returns the length of the data string
in bytes to be used for SPI search
SEARCH:SEARCH<x>:TRIGger:A:BUS:
SOUrce
Sets or returns the bus for a serial search
SEARCH:SEARCH<x>:TRIGger:A:EDGE:
SLOpe
Sets or returns the slope for an edge search
2-34 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual

Tektronix MSO2024B Specifications

General

Brand	Tektronix
Model	MSO2024B
Category	Test Equipment
Language	English