To Next Page

To Previous Page

Table of Contents

TDS Family Oscilloscope Programmer Manual

List of Tables

Table 2–1: BNF Symbols and Meanings 2–1. . . . . . . . . . . . . . . . . . . . . . . .

Table 2–2: Command Message Elements 2–2. . . . . . . . . . . . . . . . . . . . . . .

Table 2–3: Comparison of Header Off and On Responses 2–3. . . . . . . . .

Table 2–4: Acquisition Commands 2–11. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–5: Alias Commands 2–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–6: Application Menu Commands 2–12. . . . . . . . . . . . . . . . . . . . . .

Table 2–7: Calibration and Diagnostic Commands 2–13. . . . . . . . . . . . . .

Table 2–8: Cursor Commands 2–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–9: Display Commands 2–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–10: File System Commands 2–16. . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–11: Hardcopy Commands 2–17. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–12: Horizontal Commands 2–17. . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–13: Limit Test Commands 2–19. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–14: Measurement Commands 2–20. . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–15: Miscellaneous Commands 2–21. . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–16: RS-232 Commands 2–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–17: Save and Recall Commands 2–23. . . . . . . . . . . . . . . . . . . . . . .

Table 2–18: Status and Error Commands 2–23. . . . . . . . . . . . . . . . . . . . . .

Table 2–19: Trigger Commands 2–25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–20: Vertical Commands 2–31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–21: Waveform Commands 2–35. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–22: Zoom Commands 2–37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–23: Waveform Data Points Supported for Reference

Locations 2–54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–24: Commands that Affect BUSY? Response 2–60. . . . . . . . . . . .

Table 2–25: Offset Ranges for the TDS 400A, 510A, 540B, 600B, & 700A

(All Channels) and the TDS 520B, 724A, & 782A

(Channel 1 & Channel 2) using a 1x Probe 2–65. . . . . . . . . . . . . . . . . .

Table 2–26: Offset Ranges for the TDS 520B, 724A, & 782A

(Aux 1 & Aux 2) using a 1x Probe 2–65. . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–27: DATa and WFMPre Parameter Settings 2–91. . . . . . . . . . . . .

Table 2–28: XY Format Pairs 2–113. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–29: Record Length Values (<NR1>) 2–155. . . . . . . . . . . . . . . . . . . .

Table 2–30: Commands that Generate an Operation Complete

Message 2–202. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–31: Additional WFMPre Commands 2–298. . . . . . . . . . . . . . . . . . .

Tektronix TDS 500B Programmer's Manual

Other manuals for Tektronix TDS 500B