Tektronix TDS 684A - Page 376

Index
Index–8
TDS Family Oscilloscope Programmer Manual
RS-232 commands
RS232?, 2–210
RS232:BAUD, 2–207
RS232:HARDFLAGGING, 2–208
RS232:PARITY, 2–208
RS232:SOFTFLAGGING, 2–209
RS232:STOPBITS, 2–210
RS232?, 2–210
RS232: BAUD, 2–207
RS232:HARDFLAGGING, 2–208
RS232:PARITY, 2–208
RS232:SOFTFLAGGING, 2–209
RS232:STOPBITS, 2–210
*RST, 2–206
Rules, command forming, 2–1
Runt trigger, 2–249, 2–252, 2–253, 2–254, 2–255,
2–256
S
*SAV, 2–211
Save and recall command group, 2–22
Save and recall commands
ALLOCATE?, 2–52
ALLOCATE:WAVEFORM?, 2–53
ALLOCATE:WAVEFORM:FREE?, 2–53
ALLOCATE:WAVEFORM:REF<x>, 2–54
DELETE:SETUP, 2–95
DELETE:WAVEFORM, 2–96
*RCL, 2–204
RECALL:SETUP, 2–204
RECALL:WAVEFORM, 2–205
*SAV, 2–211
SAVE:SETUP, 2–211
SAVE:WAVEFORM, 2–212
SAVE:WAVEFORM:FILEFORMT, 2–213
Save setting command, 2–211
SAVE:SETUP, 2–211
SAVE:WAVEFORM, 2–212
SAVE:WAVEFORM:FILEFORMT, 2–213
SBR register, 2–217, 3–2
SDC, C–2
SELECT?, 2–214
SELECT:<wfm>, 2–215
SELECT:CONTROL?, 2–215
Selected device clear, C–2
Self test, 2–286
Separator, command, 2–2
Serial poll, 3–2
Disable, C–2
Enable, C–2
Service request enable command, 2–217
Service request enable register, 2–217
Service Requests, 1–2
SESR register, 2–68, 2–122, 2–200, 3–1
Set command, 2–1
SET?, 2–216
Sethold trigger, 2–240, 2–241, 2–242, 2–243, 2–244
Setting
Command query, 2–165
Query, 2–165
Recall command, 2–204
Save command, 2–211
Setup, Instrument preparation, 1–3
Slewrate trigger, 2–249, 2–257, 2–258, 2–259, 2–260,
2–261
SPD, C–2
SPE, C–2
*SRE command, 2–217, 3–4
SRER register, 2–202, 2–217, 3–4
SRQ, 1–2
State trigger, 2–245, 2–246
Status, 3–1
Status and error command group, 2–23
Status and error commands
*OPT, 2–201
ALLEV?, 2–51
BUSY?, 2–60
*CLS, 2–68
DESE, 2–96, 3–3
*ESE, 2–121, 3–3
*ESR?, 2–122, 3–1
EVENT?, 2–123
EVMSG?, 2–123
EVQTY?, 2–124
ID?, 2–156
*OPC, 2–200
*PSC, 2–202, 3–4
*RST, 2–206
*SRE, 2–217, 3–4
*STB?, 2–217, 3–2
*TST?, 2–286
*WAI, 2–287
Status and Events, 1–2
*STB?, 2–217
*STB? query, 3–2
Syntax
BNF (Backus-Naur form), 2–1
Command, 2–1
Diagram, 2–10
Syntax and Commands, 1–1
Syntax diagrams, 1–1