NOTE: Navigate on Autopilot is a BETA feature.
NOTE: Depending on market region, vehicle
configuration, options purchased, and software version,
your vehicle may not be equipped with Navigate on
Autopilot, or the feature may not operate exactly as
described.
When using Autosteer on a controlled-access road (such
as a highway or freeway), Navigate on Autopilot guides
Model X to o-ramps and interchanges based on your
navigation route. Along the highway portion of a
navigation route, Navigate on Autopilot also changes
lanes to prepare for exits and to minimize the driving
time to your destination.
WARNING:
Navigate on Autopilot does not make
driving autonomous. You must pay attention to the
road, keep your hands on the steering wheel at all
times, and remain aware of your navigation route.
WARNING:
As is the case with normal driving, be
extra careful around blind corners, highway
interchanges, and exits because obstacles can
appear quickly and at any time.
WARNING:
Navigate on Autopilot may not
recognize or detect oncoming vehicles, stationary
objects, and special-use lanes such as those used
exclusively for bikes, carpools, emergency vehicles,
etc. Remain alert at all times and be prepared to
take immediate action. Failure to do so can cause
damage, injury or death.
Enabling and Customizing Navigate
on Autopilot
To enable Navigate on Autopilot, touch Controls >
Autopilot > Navigate on Autopilot (Beta). Then, to
customize how you want Navigate on Autopilot to
operate, touch
CUSTOMIZE NAVIGATE ON AUTOPILOT:
•
Enable At Start Of Every Trip: Choose whether or not
you want to automatically enable Navigate on
Autopilot for every navigation route. When enabled,
the Navigate on Autopilot button on the turn-by-turn
direction list is already enabled at the start of every
trip.
•
Speed Based Lane Changes: Navigate on Autopilot is
designed to perform both route-based and speed-
based lane changes. Route-based lane changes are
designed to keep you on your navigation route (for
example, moving you into an adjacent lane to prepare
for an upcoming
o-ramp) whereas speed-based
lane changes are designed to maintain a driving
speed (not to exceed your cruising speed) that allows
you to minimize the time it takes to reach your
destination (for example, moving into an adjacent
lane to pass a vehicle in front of you). Speed-based
lanes changes are optional. You can use this setting
to disable speed-based lane changes or to specify
how aggressively you want Navigate on Autopilot to
change lanes to achieve the set cruising speed. The
MILD setting is more conservative about lane
changes and may result in a slightly longer driving
time whereas
MAD MAX is designed to allow you to
reach your destination in the shortest driving time
possible, but changes lanes only when safe to do so.
• Exit Passing Lane: Choose whether you want
Navigate on Autopilot to maneuver out of a passing
lane when navigating to a destination.
NOTE: In addition to route-based and speed-based
lane changes, Navigate on Autopilot requests a lane
change out of a passing lane as a reminder to stay in
a slower lane when you are not passing other
vehicles. Choose
NO to disable this and keep Model X
in a passing lane except when needed to stay on the
navigation route.
•
Require Lane Change Confirmation: By default,
Navigate on Autopilot requires your
confirmation
before proceeding with a lane change by pulling the
Autopilot stalk toward you or engaging the
appropriate turn signal. However, if you want
Navigate on Autopilot to change lanes without
requiring this confirmation, turn this setting o. When
you turn the setting o, you can specify if or how you
want to be notified of lane changes (O, Chime,
Vibrate, or Both).
WARNING:
If you turn o Require Lane Change
Confirmation, Navigate on Autopilot notifies
you of upcoming lane changes and o-ramps,
but it remains your responsibility to monitor the
environment and maintain control of Model X at
all times. Lane changes can occur quickly and
suddenly. Always keep your hands on the wheel
and your eyes on the driving path in front of
you.
NOTE: The touchscreen displays route-based lane
changes at the top of the map's turn-by-turn direction
list to notify you that an upcoming lane change is
needed to stay on the navigation route.
Operating Navigate on Autopilot
Once enabled, the Navigate on Autopilot button appears
on the map’s turn-by-turn direction list whenever a
navigation route is active and the route includes at least
one controlled-access road. Touch this button to allow
Navigate on Autopilot to assist you on your journey.
When enabled, the Navigate on Autopilot button is blue
and the turn-by-turn direction displays the Autosteer
icon next to the maneuvers (such as freeway exits) that
Navigate on Autopilot will handle.
Navigate on Autopilot activates and deactivates as
appropriate, based on the type of road you are driving
on. For example, if Autosteer is active and the Navigate
on Autopilot setting is turned on, Navigate on Autopilot
automatically becomes active when you reach a
supported controlled-access portion of your navigation
route.
Navigate on Autopilot
106 MODEL X Owner's Manual
To Next Page
Loading...
