TESY GH 200 - Operational Modes and Features; Manual Mode Operation; Towel Heating Function; Program Mode and Scheduling

6 Usage and Storage Instructions
EN
Manual mode:
Press .
•
start at 1800W (screen display ), the following
operation could be conducted
1. Temperature setting
•
Press SET once, the screen will ash 20°C (default
temperature is 20°C)
•
Use + or – to set temperature (5-40°C) and then
press OK to conrm setting
•
Heater will stop heating when ambient temperature
reaches the set temperature. When ambient
temperature is 2°C lower than the set temperature,
heater will restart heating.
When temperature setting nish: the screen will
automatically display the setting temperature in
working mode (SET icon and the setting temperature
will light up). Press OK to read room temperature. It will
automatically switch back to setting temperature in 5
seconds. The screen will display room temperature in
standby mode or towel heating mode. (SET icon will not
light up when room temperature is displayed only)
2. Mode Switch
Press once to switch mode among 1800W ( ), 900W
( ) and cooling fan ( ) in cycle. The relevant icon will
light up during mode switch.
Towel Heating Function
•
Connect to supply power, press once to switch on
towel heating function, to press it again to switch
it o. During towel heating mode, icon lights up
all the time. Towel heating working power is 200W.
•
Towel heating function works individually. It could
be conducted when the appliance is in standby
mode. Working period is 2 hours each time. It will
automatically switch o in 2 hours when nobody
switches it o manually.
Note: The temperature SET should be higher than
the room temperature (the temperature icon on the
left). Otherwise, the appliance will not start heating.
Program mode:
In standby mode, long press for 3 seconds, ashes
until program setting nishes:
Set Wake Up Time and Temperature:
Screen
1 2 3 4 5 6 7
full displays, which mean you are
setting wake up time for the whole week, use + and – to
set current day, the selected day will ash, press ok to
conrm. Then hour icon
1 6 12 18 24
will full
display (one box stands for one hour, totally 24 boxes for
24 hours). Use + and – and/or SET button to set hour,
the selected box will ash. You may set the start hour or
a working time range.
For example:
1. Set the heater to start at 8:00 a.m., use + and – to
select the 8th box, it will ash, press OK to conrm it.
2. Set the heater to start work at 8:00 am and stop at
10:00 a.m., rstly use + and – to select the 8th box,
then press SET, use + and – to select the 9th box,
these 2 boxes will ash, press OK to conrm it.
Then the SET temperature 20°C (default temperature
is 20°C) ashes. Use + and – to set target wake up
temperature (5-40°C).
Then press OK to move on to the next day wake up time
and temperature setting in the same way.
In the end, press OK to conrm and end the setting. All
icons will stop ashing.
(During the setting, you can press SET to activate/shut
down the wake up program for week-days.)
Note:
1. when week timer is set, icon will display all the
time. If you don’t need week timer, press once to
switch it o, the icon on screen will disappear at the
same time.
2. In week timer program, press to switch o
the current day program mode. It will works
automatically in next day as pre-set program.
Body Detector (Motion Sensor)
Body detector only works when wake up time and
temperature are set. It starts to scan the surroundings
when the preset wake-up time comes and heater starts
heating.
1. When nobody is detected, heater will stop heating
in 15 mins.
2. When somebody is detected, heater will keep
heating until the room is detected to be empty. It
will stop heating 15 mins later after that.
3. When somebody is detected again, heater will
recover to work again.