Texmo Industries TARO TSM ZRC Series

Questions and Answers

P
Pamela HayesJul 25, 2025
Why Texmo Industries Water Pump does not run?
- K
  Kristin MooreJul 26, 2025
  There are several reasons why your Texmo Industries Water Pump might not be running. It could be due to: * No power supply: Check if power is available. * Burnt motor coil: The motor may need rewinding. * Low voltage: Ensure operation within the recommended voltage range. * Tripped motor starter overload: Reset the overload, but if it trips again, check the voltage. * Pump jammed: Dismantle the pump to clear any jammed parts. * Blown fuse: Replace the fuse. * Loose connections: Tighten all electrical connections. * Prolonged idleness: Run the pump for a few minutes every other day to ensure free shaft rotation.
M
Ms. Nancy RodriguezAug 4, 2025
Why Texmo Industries Water Pump current consumption is in excess?
- E
  ebony78Aug 4, 2025
  Excessive current consumption in your Texmo Industries Water Pump can stem from several issues: * Damaged thrust bearing: Replace the worn-out bearing. * Low voltage: Check the voltage supply. * Defective rotor: Replace the rotor. * Excessive wear: Service the pump, replacing worn parts. * Low system head: Throttle the discharge.
J
Janet StephensAug 9, 2025
Why is the total head developed by my Texmo Industries Water Pump too low?
- G
  George RojasAug 9, 2025
  If your Texmo Industries Water Pump isn't developing enough head, here are a few possible reasons: * Abrasive wear: If the pump operates with water that has a high sand content or is corrosive, it can cause abrasive wear of pump hydraulics. You should change the worn-out pump parts. * Change in static head: Check the actual static head. * Low voltage: Wait for the voltage to increase.
M
Matthew HayesAug 14, 2025
How to fix a Texmo Industries Water Pump that runs rough and noisy?
- T
  Timothy BaileyAug 14, 2025
  A Texmo Industries Water Pump that runs roughly and noisily might have these problems: * Dry running: Keep the pump idle for some time or reduce the discharge by throttling. * Bent shaft: Replace the shaft. * Excessive wear: Service the pump, replacing the worn-out parts.
V
Valerie MoranAug 19, 2025
What to do if Texmo Industries Water Pump leaks excessively?
- M
  Maria CoxAug 19, 2025
  If your Texmo Industries Water Pump is leaking excessively, the cause may be: * Damaged gaskets/O-rings: Check and replace the gaskets or O-rings. * Damaged pipeline: Check and replace the piping.
L
Luis RodriguezOct 29, 2025
What to do if Texmo Industries Water Pump has less discharge?
- M
  Matthew Ferguson MDOct 29, 2025
  If your Texmo Industries Water Pump is discharging less water than expected, consider these potential causes and solutions: * Low voltage: Check the supply voltage and ensure it's within the recommended range. * Incorrect rotation direction: Interchange the supply connections of any two phases. * Excessive delivery head: Make sure the delivery head is within the specified value. * Undersized pipe: Replace the pipe with the size recommended on the nameplate. * Internal pipe deposits: Clean the discharge pipe. * Foreign objects in impellers: Inspect and remove any foreign bodies lodged in the impellers. * Partially closed/blocked valve: Check, clean, or replace the valves in the discharge pipe. * Blocked check valve: Inspect, clean, and replace the pump's check valve if nece...

Summary

Introduction

Warranty Information

Compliance Standards

Package Contents

Pump Information and Applications

Pump Schematic Diagram

Key Specifications and Features

Cross-Sectional View of Pump

Pre-Installation Requirements

Installation Procedure

Basic Troubleshooting Guide

Preventive Maintenance Checks

Operating Dos and Donts

Important Safety Instructions

Storage and Handling Guidelines

Company Contact Information

Texmo Industries TARO TSM ZRC Series Specifications

General

Category	Water Pump
Motor Power	0.5 HP to 1.5 HP
Phase	Single Phase
Pump Body Material	Cast Iron
Housing Material	Cast Iron
Shaft Material	Carbon Steel
Maximum Discharge	2200 LPH
Discharge Outlet Size	25 mm
Voltage	220 V
Mechanical Seal Material	Carbon/Ceramic