Texmo Industries Taro Pumps SSM Series

Questions and Answers

M
Michael GrantAug 8, 2025
What to do if my Texmo Industries Water Pump does not run?
- A
  Alexander HurstAug 8, 2025
  If your Texmo Industries Water Pump isn't running, start by checking if there is a power supply to the motor. If the motor coil is burnt, rewind it. Ensure you're operating within the recommended voltage range, as low voltage can be a factor. Also, check if the motor starter overload has tripped and reset it. If it trips again, check the voltage. The pump may be jammed, so dismantle it and clear any jammed parts. Replace the fuse if it has blown, and tighten any loose electrical connections. If the pump has been idle for a long time, ensure free shaft rotation by running it for a few minutes every other day.
J
James DavisAug 13, 2025
Why is my Texmo Industries Water Pump leaking excessively?
- R
  robert14Aug 13, 2025
  If your Texmo Industries Water Pump is leaking excessively, the gaskets or O-rings may be damaged, so check and replace them. Also, examine the pipeline for damage and replace any damaged sections.
J
Julie AliAug 18, 2025
Why Texmo Industries Water Pump has less discharge?
- J
  jacobwebbAug 18, 2025
  If your Texmo Industries Water Pump has less discharge, start by checking the supply voltage and ensure it's operating within the recommended range. The wrong direction of rotation could also be the cause. Ensure the delivery head is within the specified value. Also, if a smaller pipe size is used compared to nameplate recommendations, replace it with the suggested pipe size.
M
Madison BradshawAug 22, 2025
How to fix low total head developed in Texmo Industries Taro Pumps SSM?
- M
  Matthew OchoaAug 22, 2025
  To address low total head in your Texmo Industries Water Pump, consider these points. Abrasive wear of pump hydraulics might be the cause if you're operating in water with higher sand content or corrosiveness, in this case change the worn-out pump parts. If the pump is running at low voltage, wait for the voltage to increase or contact your local EB representative. Low system head can also lead to higher discharge, so throttle the discharge to adjust.
K
Karen SilvaAug 28, 2025
Why Texmo Industries Taro Pumps SSM runs rough and noisy?
- M
  Melanie BrayAug 28, 2025
  If your Texmo Industries Water Pump runs rough and noisy, it may be due to dry running of the pump. Keep the pump idle for some time or reduce the discharge by throttling. A bent shaft could also be the issue, so replace the shaft if necessary. Excessive wear and tear can also cause this problem, so service the pump, replacing the worn-out parts.
P
Paul LevineSep 2, 2025
What to do if Texmo Industries Water Pump has less discharge?
- C
  cindymoraSep 2, 2025
  If your Texmo Industries Water Pump has less discharge, start by cleaning the discharge pipe if it's internally coated with depositions. Check the impellers for any foreign bodies and remove them. Also, inspect the valve in the discharge pipe to ensure it is not partly closed or blocked; clean or replace the valve if necessary. Check and clean the NRV and replace it if necessary. Finally, check the pipework for any leakage and repair or replace the piping.

Summary

Information about your pump

Key specifications & features

Standard Technical Specifications

Core Product Features

Electrical Connection Details

Cross-section view

Pre-installation Requirements

Installation Arrangement

Guidelines for arranging the installation site and personnel.

General Installation Precautions

Essential precautions for ensuring a correct and safe pump installation process.

Safety and Operation Precautions

Safety Notes and Warnings

Important safety notes, warnings, and cautions for pump handling and operation.

Operation Precautions

Crucial precautions for operating the pump safely, including liquid temperature and running dry prohibitions.

Installation Procedure

Installation Steps

A sequential guide outlining the steps for installing the submersible monoblock pump, including initial checks.

Flooded Suction and Filling Method

Motor Cable Joint Waterproofing

Cable Joint Safety and Waterproofing Procedure

Emphasizes safety warnings and the process for waterproofing the submersible motor cable joint.

Rotation Check and Electrical Installation

Electrical Installation Guidelines

Electrical Wiring and Earthing

Proper Earthing Connections

Power Supply Connection

Power Connection Safety Cautions

Basic Troubleshooting

Common Faults and Solutions

A table detailing common pump faults, their causes, and suggested corrective actions.

Troubleshooting Specific Issues

Further guidance for specific operational problems like reduced discharge, noise, and leaks.

Preventive Maintenance Checks

Maintenance Safety Precautions

Essential safety precautions to follow before commencing any maintenance or inspection activities.

Performance Monitoring and Checks

Dos and Donts

Installation and Operation Best Practices

Important Safety Instructions

Qualified Personnel and Safety

Texmo Industries Taro Pumps SSM Series Specifications

General

Type	Submersible Pump
Material	Stainless Steel
Pump Shaft	Stainless Steel
Model	SSM Series
Application	Agricultural, Domestic, Industrial
Outlet Size	1 inch
Impeller Material	Stainless Steel