Thermo Scientific Lindberg Blue M 3055 Series User Manual

Thermo Scientific Lindberg Blue M 3055 Series

34 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Lindberg Blue M

Performance Ovens

3055 and 3056 Series

Operating Manual and Parts List LT2148X3 Rev. 0

_________________________________________________________________________________

Part of Thermo Fisher Scientific

Questions and Answers:

T
thomasjenkinsAug 6, 2025
What to do if alarm LED stays on and control is higher than set temperature in Thermo Scientific Oven?
- T
  Tyler MyersAug 6, 2025
  If the alarm LED remains illuminated and the control indicates a temperature exceeding the set point, it could be due to several reasons. The set temperature might have been adjusted to a value lower than the actual temperature, minus the high alarm limit, in which case you should wait for the actual temperature to cool down to the set temperature. Alternatively, there may be a defective controller, which would require replacement. Finally, defective solid state relays or safety relays could also be the cause; in this case, refer to the schematic and replace the relays.
B
Brittany RobertsonAug 18, 2025
Why is my Thermo Scientific Lindberg Blue M 3055 temperature erratically high?
- J
  Jesse GonzalezAug 18, 2025
  If your Thermo Scientific Oven's temperature is erratically high, the most likely cause is a defective control thermocouple, which would need to be replaced.
K
kerraaronAug 25, 2025
What to do if Thermo Scientific Lindberg Blue M 3055 set display shows 'EEE'?
- B
  Brian CooperAug 25, 2025
  If the set display of your Thermo Scientific Oven shows 'EEE', it could indicate a few potential issues. It's possible that the set temperature has been changed to a value less than the actual temperature minus the high alarm limit; in this case, wait for the actual temperature to cool to the set temperature. Another possibility is a defective control thermocouple, which would need replacing. Lastly, faulty or broken connections could be the cause, so check the thermocouple connections at the rear of the temperature controller.
A
Autumn ReidAug 29, 2025
How to fix no power in Thermo Scientific Lindberg Blue M 3055 Oven?
- T
  Thomas HessAug 29, 2025
  If your Thermo Scientific Oven has no power, first ensure that the unit is properly plugged in and turned on. If it is, the issue might be a defective circuit breaker, which would need to be replaced.

Thermo Scientific Lindberg Blue M 3055 Series Specifications

General

Brand	Thermo Scientific
Model	Lindberg Blue M 3055 Series
Category	Oven
Language	English

Summary

Section 1 Introduction

Section 2 Specifications

Section 3 Installation

Unpacking

Procedures for unpacking the oven and its components.

Preparing the Oven

Steps to prepare the oven for operation after unpacking.

Power Switch

Details about the front panel power switch and circuit breaker.

Section 4 Controls

Display

Explains the LED numeric display and indicator lights.

Keypad

Describes the four-key tactile keypad and its functions.

Section 5 Operation

Safety Precautions

Lists general safety guidelines for operating the oven.

Limit Alarm

Explains the deviation alarm and its behavior.

Display Offsets

How to select and adjust display offset temperatures for calibration.

Section 6 Service

Replacing the Door Gasket

Procedure to replace the oven's door gasket.

Replacing the Door Handle

Steps to replace the oven door handle.

Adjusting the Door Cam

How to adjust the door cam for proper closing and sealing.

Accessing Electronics Compartment

Steps to gain access to the oven's electronics compartment.

Replacing the Heater

Procedure for replacing the oven's heating element.

Replacing the Cooling Fan

Steps to replace the cooling fan.

Replacing Circulating Fan Motor

Procedure to replace the circulating fan motor.

Replacing the Controller

Steps to replace the oven's control unit.

Replacing the Solid State Relay

Procedure to replace the solid state relay.

Replacing the Safety Relay

Steps to replace the safety relay.

Replacing the Control Thermocouple

Procedure to replace the control thermocouple.

Section 7 Troubleshooting

Section 8 Replacement Parts

Section 8 Schematics

Related product manuals

Lindberg/Blue M VO Series

Preview: Thermo Scientific OGH 60 Series

Thermo Scientific OGH 60 Series

Preview: Thermo Scientific PR305225G

Thermo Scientific PR305225G

Thermo Scientific OMH 60 Series

Thermo Scientific OMH 100 Series

OGH 100-S Series

Thermo Scientific OMH 400 Series

Thermo Scientific OMH 180 Series

Thermo Scientific OMH 750 Series

Thermo Scientific NAPCO 6508