Thermo Scientific Steri-Cycle i160 CR User Manual (English)

To Next Page

50163206 March 2021

Thermo Scientific

Steri-Cycle i160 CR/

Steri-Cycle i250 CR

Incubator

Operating Instructions

Table of Contents3
General Notes13
Identification of the Device and of the Documentation13
- Identification of the Device13
Instruction of the Operating Personnel13
Applicability of the Instructions14
- Original Document for Translation14
Warranty14
- Requirements for Warranty14
Explanation of Safety Information and Symbols15
- Safety Information and Symbols used in the Operating Instructions15
- Additional Symbols for Safety Information:16
- Symbols on the Device17
Intended Purpose of the Device17
- Correct Use17
- Incorrect Use18
Standards and Directives18
Safety Notes on Gases19
- Instruction of the Personnel:19
- Safety Notes on Carbon Dioxide (CO2)19
- Safety Notes on Oxygen (O2)20
- Safety Notes on Nitrogen (N2)20
Packaging21
Examination on Receipt21
Standard equipment Components Steri-Cycle i160 / i250 CR22
Optional Equipment Components Steri-Cycle i160 / i250 CR22
Optional Equipment Components Steri-Cycle i160 / i250 CR23
Optional Equipment Components Steri-Cycle i160 / i250 CR23
Environmental Conditions25
- Requirements:25
Site Ventilation26
Space Requirements26
Transport27
Stacking28
- Stacking Variants31
- Installing the Support Stand with Castors31
- Support Stand with Castors and Supporting Feet (160i and 250i Unit)32
- Installing the Floor Stand, 780 mm34
Retrofitting/Modifications35
Steri-Cycle i160 / i250 CR Front View38
Steri-Cycle i160 / i250 CR Back View40
Safety Devices Steri-Cycle i160 / i250 CR40
Workspace Atmosphere41
- Temperature:41
- Relative Humidity:41
- Water Quality Recommendations:41
- Prefilter42
- HEPA-Filter and Air Duct42
- CO2 Supply:44
- O2 Supply:44
- N2 Supply:45
Door Switch46
Sensor System46
Supply Interface49
- Standard Interfaces49
- Gas Connection:50
- USB Interface:50
- 4-20 mA Interface:50
- Alarm Contact:52
- Power Supply Connection:52
Workspace Components52
- Inner Container52
- Glass Door and Optional Gas-Tight Screen53
- Water Reservoir54
Water Filling56
- Heating System56
- Rear Panel Openings57
- Shelf System58
Electromechanical Door Lock59
Adapting the Unit to the Ambient Atmosphere61
Preparing the Workspace61
Installing the “MAX” Fill Level Indicator and the Prefilter62
Installing the HEPA Filter in the Rear Wall Filter Enclosure64
Install the Air Duct64
Installing the HEPA-Filter and the Water Reservoir Cover Panel66
Installing the HEPA Filter in the Rear Panel69
Installing the Shelf System69
- Installation/Removal of the Support Rail69
- Shelf Support Installation70
- Levelling the Device71
Mounting the Split Inserts (Optional) into the Steri-Cycle i250 CR71
Gas Connection72
- Installing Gas Pressure Hoses72
- Gas Connection73
Mains Connection74
Connecting the USB Interface:75
Connecting the Alarm Contact:75
Connecting the 4-20 mA Interface:77
Preparing the Device79
Starting Operation80
Water Filling81
Power Switch86
Operating Panel and Operating Structure87
- Versions without O2/N2 Control88
- Version with combined CO2/O2/N2 Control (Optional)89
- Structure of the Operating Levels89
Factory Presettings of the iCan™ Touchscreen Controls91
Heat-up Phase of the Control Loop Sensors91
Behavior of Keys during Adjustments92
Setting the Temperature Set Value92
Setting the CO2 Set Value93
Setting the O2 Set Value94
Auto-Start Function96
- Activating the Auto-Start Routine98
- Interrupting the Auto-Start Routine99
Launching Steri-run100
User Configuration101
- Settings / Setup101
- Data Logging111
- Options115
- Icon Description124
- Enabling/Disabling the Keypad Lock125
- Software Versions126
Scaling the Trend Display126
Error Messages128
- Response to an Error Message Event128
- Resetting Overtemperature Protection129
- Measures After Power Outage130
- Troubleshooting131
Shutting the Device Down137
Cleaning139
Decontamination Procedures140
Preparing for Disinfection / Steri-run140
Wipe/Spray Disinfection of the Workspace141
Steri-run Decontamination Routine145
- Progress of a Steri-run Decontamination Routine:146
- Activate Steri-run148
- Canceling Steri-run149
- Steri-run Interruption due to Error150
- Completing Steri-run151
- Opening the Door after Canceling Steri-run152
Inspections and Checks153
Service Intervals154
Preparing Temperature Calibration154
Temperature Calibration Procedure155
Preparing the CO2 Calibration157
CO2 Calibration Procedure158
Replacing the HEPA Filter in the Workspace159
Replacing the HEPA Filter in the Rear Wall Filter Enclosure162
Replacing the Gas Inlet Filter162
Device Fusing Replacement163
Replacing the Outer Door Seal163
Spare Parts164
Overview of the Materials Used:165
Steri-Cycle i160 CR168
Steri-Cycle i160 CR170
Steri-Cycle i250 CR172
Steri-Cycle i250 CR174
- USB Interface177
- Installing the USB Port Driver178
Structure of the Command Sequences for Data Communication180
- Description of Protocol180
Overview of General Parameters (Addresses 0xxx)181
- Reading General Parameters181
Overview of Incubator Parameters (Addresses 2xxx)181
- Reading Basic Parameters182
- Reading Internal Function Parameters183
Error Memory Structure184
- Error Memory Data Set Structure Scheme:185
- Overview of the Possible Error Messages in Hex Coding186
- Overview of the Possible Error Messages in Bit Coding General Device Status, Temperature and CO2 Control Loop:186
- O2 Control Loop and Water Level:187
Data Logger Structure187
- Data Logger Data Set Structure Scheme:189
- Overview of Possible Event Entries in Bit Coding Overview of Event Entries, Part I:190
- Overview of Event Entries, Part II:191
Examples of Data Logger Codes191
- Functions for Data Logger Queries192
- Example of a Code for a a Data Logger Query192
Program Steri-Cycle i160 / i250 CR197
- Installing the Steri-Cycle i160 CR & Steri-Cycle i250 CR198
- Operating the Steri-Cycle i160 CR & Steri-Cycle i250 CR199
Installation of the Shelving212

Brand	Thermo Scientific
Model	Steri-Cycle i160 CR
Category	Laboratory Equipment
Language	English

Thermo Scientific Steri-Cycle i160 CR User Manual

Table of Contents

Thermo Scientific Steri-Cycle i160 CR Specifications

Related product manuals