DVI OUT 2
VQM-2 Dual
Video
DVI OUT 2
VQM-3V Dual
Video
QUICK-START GUIDE
QUICK-START GUIDE
As used with Thinklogical’s® Q-Series and
Velocitydvi-3 Video Extension Systems
Complete Steps 1-8 to connect to the VX80 Router:
STEP 1: Connect the VQM-3V Receiver Modules to the VX80
Router using multi-mode fiber-optic cables (up to 1000 meters).
Connect fiber L1 to any Downstream SFP’s Transmit Port and fiber
L2 to the same SFP’s Receive Port.
STEP 2: Ensure the Q-4300 Power Supply switches on the front
panel are in the OFF position. Install the Right Power Supply
Module AC Power Cord (left receptacle) and the Left Power
Supply Module AC Power Cord (right receptacle) onto the Q-4300
Chassis. Plug each cord into a standard AC source. On the front of
the chassis, turn ON the Right and Left Power Supply Modules.
On the VelocityDVI Receiver, connect the +5VDC Adapter (PWR-
000022-R) to the unit and plug it into a standard AC source.
STEP 4: Connect the VQM-3V Transmitter Modules to the
VX80 Router using multi-mode fiber-optic cables (up to 1000
meters). Connect fiber L1 to any Upstream SFP’s Receive Port
and fiber L2 to the same SFP’s Transmit Port.
STEP 5: Ensure the Q-4300 Power Supply switches on the
front panel are in the OFF position. Install the Right Power
Supply Module AC Power Cord (left receptacle) and the Left
Power Supply Module AC Power Cord (right receptacle) onto
the Q-4300 Chassis. Plug each cord into a standard AC source.
On the front of the chassis, turn ON the Right and Left Power
Supply Modules.
STEP 6: Connect DVI cables from the Source CPUs to the DVI
IN ports of each Transmitter. Connect the Stereo 3D sources
from the CPU to the Transmitters with standard BNC cables.
Ensure the CPUs are turned ON.
STEP 7: Connect the VX80 Controller Cards’ LAN Ports to
your Controller CPU with CAT5 cables.
(CPU IP address: 192.168.13.9)
STEP 8: Connect both supplied AC Power Cords
(PWR-0000006-R) to the receptacles located on
the VX80's power supplies. Plug each one into a
standard AC source. Verify that all system functions
are operating properly.
VX80_VQM-3V_to_VQM-3V_VEL-3_QSG_manual
with VQM-3V Dual Video Transmitter & Receiver Modules
VQM-3V Dual-Video Tx
VQM-00V003-LCTX
2
8
Q-4300 Chassis
VQS-004300
VX80 Router KVM Matrix Switch Chassis, 6 Rack Units, 400 Watts
DVI IN 1
Source CPUs 7 & 8
VQM-3V Dual Video Rx
VQM-00V003-LCRX
Q-4300 Chassis
VQS-004300
DVI OUT 1
VQM-3V
Dual Video 1
DVI OUT 2
VQM-3 Dual
Video
DVI OUT 1
VQM-3V
Dual Video 3
DVI OUT 1
VQM-3V
Dual Video 4
3
L1: Data TX to RX and Video
L2: Data RX to TX
DVI OUT 1
VQM-3V
Dual Video 2
DVI IN 2
DVI IN 1
Source CPUs 5 & 6
DVI IN 2
DVI IN 1
Source CPUs 3 & 4
DVI IN 2
DVI IN 1
Stereo 3-D
Source CPUs 1 & 2
6
DVI IN 2
Stereo 3-D
Stereo 3-D
Stereo 3-D
4
Network Hub
Optional Secondary Controller Card
IP address: 192.168.13.16
Primary Controller Card
IP Address: 192.168.13.15
External Control CPU
7
To LAN Ports
3D OUT 1 3D OUT 2 3D OUT 3 3D OUT 4
DVI OUT 2
VQM-3V
4 (DDC)
DVI OUT 2
VQM-3V
Dual Video 4
1 2 3 4
1 2 3 4
PWR-000022-R
2
3
1
VelocityDVI-3 Rx
VEL-000M03-LCRX
DVI OUT 2
VQM-3 Dual
Video
5
STEP 3: Depending on the
configuration, connect the
peripheral devices (monitors,
Stereo 3D, etc.) to the Receivers
using standard copper cables.
Turn all the devices ON.
KVM Matrix Switch
Powered by
MRTS Technology
VX80
router
To Next Page
Loading...