Local
DVI OUT
Module 1
Local
DVI OUT
Module 2
Local
DVI OUT
Module 3
Local
DVI OUT
Module 4
DVI OUT DDC
Module 1
DVI OUT DDC
Module 2
DVI OUT DDC
Module 3
DVI OUT DDC
Module 4
DVI IN
Module 4
DVI IN
Module 3
DVI IN
Module 2
DVI IN
Module 1
Source CPU
L1: Data TX to RX and Video
L2: Data RX to TX
External Control CPU
Network Hub
7
Optional Secondary
Controller Card
IP address: 192.168.13.116
Primary Controller
Card IP Address:
192.168.13.115
As used with the
Q-Series Single-Link
Fiber-Optic Extension
System
2
1
3
4
6
STEP 6: Connect a DVI cable from the Source CPU
to the DVI IN port of each Transmitter Module. If
desired, connect an optional local monitor to each
of the Transmitters’ DVI OUT ports with a standard
DVI cable. If stereo 3-D molecular visualization at
the destination is desired, connect the Stereo
Source’s OUTPUT to the Transmitter Module’s
STEREO INPUT.
Ensure the sources are turned ON.
8
STEP 7: Connect the Controller Cards’ LAN Ports
to your Controller CPU with CAT5 cables.
(CPU IP address: 192.168.13.9)
STEP 8: Connect both supplied AC Power Cords
(PWR-0000056-R) to the receptacles located on the
VX160's power supplies. Plug each one into a
standard AC source. Verify that all system functions
are operating properly.
DVI OUT
Module 1
DVI OUT
Module 2
DVI OUT
Module 3
DVI OUT
Module 4
3D Stereo Emitter
STEP 1: Connect the Q-Series Receiver Modules
to the VX160 using multi-mode fiber-optic cables
(up to 1000 meters). Connect fiber L1 to any SFP’s
Transmit Port and fiber L2 to the same SFP’s
Receive Port. Do the same for each of the Receiver
modules.
STEP 2: Ensure the Q-4300 Power Supply
switches on the front panel are in the OFF position.
Install the Right Power Supply Module AC Power
Cord (left receptacle) and the Left Power Supply
Module AC Power Cord (right receptacle) onto the
Q-4300 Chassis. Plug both cords into a standard
AC source. On the front of the chassis, turn ON the
Right and Left Power Supply Modules.
STEP 3: Connect a monitor to each of the DVI OUT
DDC ports with a standard DVI cable. A second,
non-DDC monitor may also be connected to each
modules’ DVI OUT port. If stereo 3-D molecular
visualization on your desktop is desired, connect a
3-D Active Stereo Emitter to the STEREO OUT
receptacle on the Receive module.
STEP 4: Connect the Q-Series Transmitter
Modules to the VX160 using multi-mode fiber-
optic cables (up to 1000 meters). Connect fiber
L1 to any SFP’s Receive Port and fiber L2 to the
same SFP’s Transmit Port. Do the same for each
of the four Transmitter modules.
STEP 5: Ensure the Q-4300 Power Supply
switches on the front panel are in the OFF
position. Install the Right Power Supply Module
AC Power Cord (left receptacle) and the Left
Power Supply Module AC Power Cord (right
receptacle) onto the Q-4300 Chassis. Plug each
cord into a standard AC source. On the front of the
chassis, turn ON the Right and Left Power Supply
Modules.
VQM-3 Transmitters (4)
VQM-000003-LCTX
Q-4300 Chassis
VQS-004300
VQM-3 Receivers (4)
VQM-000003-LCRX
Q-4300 Chassis
VQS-004300
VX160 Router Chassis
VXR-000160
16 Rack Units, 850 Watts
Upstream Data Card (8)
VXM-DI0020
Downstream Data Card (8)
VXM-DO0020
Controller Card (2)
VXM-000001
QUICK-START GUIDE
QUICK-START GUIDE
KVM Matrix Switch
Powered by
MRTS Technology
VX160
router
Complete Steps 1-8 to connect
to a VX160 KVM Matrix Switch
®
5
3D Stereo
Emitter
Tx
Rx
SFP
Tx
Rx
SFP
To Next Page
Loading...