01
Important Safety Instructions
SAVE THESE INSTRUCTIONS: To reduce the risks of fire or explosion, electrical shock and the injury to
persons, read and understand all instructions included in this manual. Be familiar with the controls and the
proper usage of the equipment.
► Exhaust and fresh air introduction must be provided to keep the air within the spray area free from
accumulation of flammable vapors.
► Avoid all ignition sources such as static electricity sparks, open flames, pilot lights, hot objects, lit
tobacco products, and sparks from connecting and disconnecting power cords or working light switches.
► Fire extinguisher equipment shall be present and working.
► Keep area clean and free of paint or solvent containers,rags,and other flammable materials.
► Follow the material and solvent manufacturer’s safety precautions and warnings.
► Do not spray flammable or combustible materials near an open flame or sources of ignition such as lit
tobacco products, motors, and electrical equipment.
► Know the contents of the spray materials and their cleaning solvents. Read all Material Safety Data
Sheets (MSDS) and container labels provided with the spray materials and solvents. Follow the spray
material and solvent manufacturer’s safety instructions.
► Do not use materials with a flashpoint higher than 60ºC (140ºF). Flashpoint is the temperature (see
coating supplies).
► Do not use bleach.
► Do not use halogenated hydrocarbon solvents such as methylene chloride and trichloroethane. They
are not compatible with aluminum and may cause an explosion. If you are unsure of a material’s compati-
bility with aluminum, contact your coating supplier.
► Use a respirator or mask if vapors can be inhaled.
► Wear protective eyewear.
► Wear protective clothing as required by coating manufacturer.
► Always use appropriate gloves.
► Keep electrical cord plug and sprayer trigger free from spray material and other liquids. Never hold cord
at plug connections to support cord. Failure to observe may result in an electrical shock.
► Never immerse electrical parts in water or any other liquid. Wipe the exterior of the sprayer with a damp
cloth for cleaning. Always make sure the sprayer is unplugged before taking it apart for cleaning.
► Do not expose unit to rain or wet conditions.
► Do not abuse the cord. Never use the cord to carry the unit or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.
► Children should stay away from the sprayer to prevent them from eating metal and plastic parts by
accident.
► Oil-based paint contains harmful substances such as formaldehyde, which does not meet environmental
protection requirements. Please pay attention to protection during use.
► When using an extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. If an
extension cord is to be used outdoors,it must be marked with the suffix W-A after the cord type designation.
For example, a designation of SJTW-A would indicate that the cord would be appropriate for outdoor use.
For proper size cords see the following data:
●
Up to 5 metres:2x 1.0 mm²
●
From 5 to 10 metres:2x 1.5 mm²
Technical Data
● Power Source:4.6A(550W), 120V~60Hz(US)
● Max. Atomisation Power:180W
● Motor Speed:35000 RPM
● Max. Viscosity:100 DIN-s(runout time: 100 seconds)
● Canister Capacity:35 fluid oz(1000 mL)
● Nozzle Size:Φ1.0mm,Φ1.5mm,Φ1.8mm,Φ2.0mm,Φ2.5mm
● Sound Pressure Output:80 dB
● Oscillation Level:< 2.5 m/s²
● Paint Fluid Delivery:10~14 fluid oz/min(300 ~ 400 mL/min)
● Water Flow Rate:30 fluid oz/min(900 mL/min)
● Performance:
27 ft²/min(2.5m²/min)
●
Power cord length: 60” (1.5m).
To Next Page
Loading...