What to do if my Tokyo Hy-Power HL-1.5KFX Amplifier shows TVI, FMI?
If your Tokyo Hy-Power Amplifier shows TVI/FMI, try the following: * Decrease the drive. * Check the ALC setting. * Insert common mode filters on the antenna cable or AC line. * Add clamp-on ferrite cores (TDK, Amidon, Palomar) on various cables.
What to do if my Tokyo Hy-Power HL-1.5KFX's AC mains are not operating?
If the AC mains are not operating on your Tokyo Hy-Power Amplifier, try the following: * Replace with new ones. * Plug in securely. * Screw bolts tightly on the top cover. * Correct primary wiring.
Why does the O.Heat light turn on in my Tokyo Hy-Power Amplifier?
The O.Heat light on your Tokyo Hy-Power Amplifier indicates that the internal temperature is above 70 degrees Celsius. Let the unit cool off until the LED turns off. Also, check for any air intake blockages and ensure the air vent on the top cover is clear.
What to do if my Tokyo Hy-Power Amplifier can’t enter transmit mode?
If your Tokyo Hy-Power Amplifier can’t enter transmit mode, check the cable and ensure it's properly connected. Also, check the drive power, antenna SWR, and antenna selector A/B. You can also try resetting the unit with the AC power switch.
What does it mean if the O.Drive lights are on in my Tokyo Hy-Power Amplifier?
If the O.Drive lights are on in your Tokyo Hy-Power Amplifier, decrease the drive. Also, ensure that the BAND is correctly matched in Manual mode.
What does it mean when the PR lights illuminate on my Tokyo Hy-Power Amplifier?
If the PR lights are illuminated on your Tokyo Hy-Power Amplifier, check and adjust the antenna, or decrease the drive. Also, check the coax cable connectors.
What should I do if the FUSE lights are on in my Tokyo Hy-Power Amplifier?
If the FUSE lights are on in your Tokyo Hy-Power Amplifier, replace F202 and F203 (20A) on the PA board (PC1662V). Also, adjust the antenna.
Overview of the HL-1.5KFX amplifier and its key features.
Essential safety warnings and proper handling instructions for operating the amplifier.
Guidance on configuring the amplifier for different AC voltage inputs and safety.
Detailed explanation of the amplifier's advanced features and capabilities.
Comprehensive list of technical parameters, performance data, and requirements for the amplifier.
Identification and function of controls, switches, LEDs, and the meter on the front panel.
Description of connectors and controls located on the rear panel of the amplifier.
Details regarding the AC voltage selection switch and fuse socket on the amplifier's chassis bottom.
Illustrative diagrams for connecting the amplifier in one and two antenna system configurations.
Instructions for correctly connecting and adjusting the Automatic Level Control (ALC) system.
Detailed guide for connecting band data cables for ICOM, Yaesu, and Kenwood transceivers.
Explanation of the five major protection circuits and the conditions that trigger them.
Overview and signal flow of key internal circuits, including DC power, PA, and LPF.
Guide to diagnosing and resolving common operational issues and error indicators.
List of compatible transceivers for auto band setting from major manufacturers.
Detailed diagram showing the placement of major internal components on the amplifier's top surface.
Views of the Main Control board (front, top, bottom) detailing component placement.
Layout details for the Power Amplifier (PC1662V) and Low Pass Filter (PC1681) boards.
Layout diagrams for the RF Power Detector, Prescaler, DC-DC Converter, and Surge Absorber.
Diagrams illustrating pin assignments for Kenwood, Yaesu, and Tuner connectors on the rear panel.
General| Brand | Tokyo Hy-Power |
|---|---|
| Model | HL-1.5KFX |
| Category | Amplifier |
| Language | English |
To Next Page
