• Pressure Range: 40 – 100 PSI (2.8 – 7.0 kg/cm
2
) (276 – 689 kPa)
• Nozzle Performance
@ Optimum Pressure: 60 PSI (4.2 kg/cm
2
) (414 kPa)
*Precipitation rates are for triangular spacing at 50% of diameter.
• Nozzle Trajectory: 25°
• Arc Range: 30° – 360°
• Inlet Thread Size: 1" female NPT or 25mm female BSP
• Nozzle Pop-Up Height: 4" (102mm)
• Overall Height (Nozzle Retracted): 8.75" (222mm)
If sprinkler nozzle change is required,
refer to the nozzle specifications above
to select appropriate nozzle and install as follows:
Nozzle Installation
Installation Instructions
2001
®
Series Sprinkler
Specifications
Install sprinkler to lateral line using a triple swing joint
connection as shown. Position top of sprinkler cap flush
with finish grade. Tilt sprinkler as required to maintain perpendicular alignment with finish
grade. If installing a part-circle sprinkler, tighten sprinkler on swing joint aligning long rib on
body with left watering border. The sprinkler arc is factory preset to 180°. If arc adjustment is
required, see arc adjustment instructions below.
Clockwise travel reversing point is adjustable to provide
30° thru 360°of arc. Counterclockwise travel reversing point
is non-adjustable (fixed) and is established when the long sprinkler body rib is aligned with the
left watering border. As nozzle begins clockwise travel from left border, adjust arc as follows:
Sprinkler Installation
Increase
Insert tool blade through center of nozzle turret to
engage slot. Turn blade clockwise to decrease arc or
counterclockwise to increase arc. Each
“
click” is
equal to 3° of arc change. Observe new arc path as
nozzle sweeps back and forth. Repeat procedure as
necessary to fine-tune.
Note: To expedite arc adjustment process, turn nozzle
turret by hand in current direction of travel, releasing
turret before reversing point.
Decrease
Insert tool blade
through top of
nozzle turret as
shown. Twist 1/4
turn to engage.
Lift riser assembly.
Grasp riser firmly
below nozzle turret
to prevent
retraction.
Thread nozzles
into turret using
socket end of tool.
Align lower nozzle
as shown.
1 – 1" x 3" (25mm x 76mm) Nipple
2 – 1" (25mm) Ell
3 – 1" (25mm) Street Ell
4 – 1" x 12" (25mm x 305mm) Nipple
5 – Lateral Tee
Caution: Do not use pipe
dope on plastic threads –
severe damage will result.
Swing Joint Components
Finish Grade
Arc Adjustment
Align long rib with left
watering border.
© 2000 The Toro Company, Irrigation Division Form Number 368-0006 Rev. H
Main Color Inner Radius GPM Prec. Rate* Radius LPM Prec. Rate*
Nozzle Nozzle in Feet In./Hr. in Meters mm/Hr.
#6 Yellow Gray 51 7.1 0.23 15.6 26.9 5.8
#9 Orange Gray 52 10.2 0.31 15.9 38.6 8.0
#12 Brown Red 53 13.0 0.39 16.2 49.1 9.8
#15 Gray Red 57 16.1 0.41 17.4 60.9 10.5
#18 Blue Red 59 18.9 0.45 18.0 71.3 11.4
#24 Green Red 60 23.3 0.54 18.3 88.2 13.7
To Next Page
Need help?
General
