To Next PageTo Next PageWhy won't my Toro 74182 Lawn Mower engine start?
If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, you can try the following: Fill the fuel tank with gasoline, move the choke lever to the ON position, clean or replace the air cleaner element, install wires on the spark plug, install new, correctly gapped spark plugs, or replace the fuel filter.
How to fix Toro 74182 engine that will not start?
If your Toro Lawn Mower engine won't start, starts with difficulty, or struggles to stay running, try these steps: first, ensure the fuel tank is filled with gasoline. Then, move the choke lever to the ON position. After that, clean or replace the air cleaner element. Also, make sure the wires are securely installed on the spark plug and install new spark plugs with the correct gap. Lastly, replace the fuel filter.
What to do if Toro Lawn Mower starter does not crank?
If the starter on your Toro Lawn Mower isn't cranking, make sure the power take off (PTO) is disengaged and the parking brake is set. Also, ensure the motion control levers are in neutral. Check that the battery is charged and all electrical connections have good contact. Finally, try replacing the fuse.
What to do if my Toro Lawn Mower starter does not crank?
If the starter on your Toro Lawn Mower doesn't crank, make sure to move the power take off (PTO) to DISENGAGED, set the parking brake, and move the motion control levers into neutral. You should also charge the battery, check electrical connections for good contact, and replace the fuse.
How to fix a Toro Lawn Mower engine that loses power?
If your Toro Lawn Mower engine loses power, try these steps: reduce ground speed, clean the air cleaner element, add oil to the crankcase, remove any obstructions from the cooling fins and air passages, install new, correctly gapped spark plugs, and replace the fuel filter.
What to do if my Toro 74182 doesn't drive?
If your Toro Lawn Mower doesn't drive, make sure the parking brake is off and add hydro fluid to the reservoir.
How to stop abnormal vibration in my Toro 74182?
To address abnormal vibration in your Toro Lawn Mower, tighten the engine mounting bolts and the appropriate pulley.
What to do if my Toro 74182 engine overheats?
If your Toro Lawn Mower engine overheats, reduce the ground speed. Add oil to the crankcase and remove any obstructions from the cooling fins and air passages.
What to do if my Toro 74182 does not drive?
If your Toro Lawn Mower doesn't drive, ensure the parking brake is off and add hydro fluid to the reservoir.
How to fix abnormal vibration in Toro Lawn Mower?
If you notice abnormal vibration in your Toro Lawn Mower, tighten the engine mounting bolts and the appropriate pulley.
General| Engine Type | 4-Cycle |
|---|---|
| Drive System | Self-Propelled |
| Deck Material | Steel |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Engine | Briggs & Stratton |
| Fuel Capacity | 0.33 gallons |
| Oil Capacity | 20 oz |
| Fuel Tank Capacity | 0.33 gallons |
| Start Type | Pull Cord |
General safety instructions for operating the machine safely to prevent injury.
Details critical safety precautions and prohibited actions when operating on slopes to prevent accidents.
Outlines specific safety measures to prevent injuries involving children around the machine.
Illustrates how to measure slopes and provides visual guidelines for safe operation on inclines.
Emphasizes the importance of reviewing safety instructions before operating the machine.
Provides step-by-step instructions for starting the engine safely and correctly.
Details the procedure for safely stopping the engine and the machine.
Explains how the safety interlock system prevents starting or stops the engine under certain conditions.
Provides a schedule for performing various maintenance tasks based on operating hours.
Details engine oil type, capacity, and change intervals.
Guidance on checking and maintaining hydraulic fluid levels and filters.
Lists possible causes and corrective actions when the starter motor fails to crank.
Addresses common problems with engine starting and running, providing solutions.
Identifies reasons for loss of engine power and suggests corrective actions.
Explains why the engine might overheat and how to resolve the issue.
Provides solutions for when the machine fails to move.
