Why is there abnormal vibration in my Toro 74266 Lawn Mower?
If your Toro Lawn Mower is experiencing abnormal vibration, install new cutting blade(s). Tighten the blade mounting bolt, engine mounting bolts, and the appropriate pulley (engine, idler, or blade pulley). For issues with the engine pulley, blade spindle, or motor mount, contact an Authorized Service Dealer.
What to do if my Toro 74266 Lawn Mower engine does not start?
If your Toro Lawn Mower engine doesn't start, starts hard, or fails to keep running, several factors could be at play. Start by checking if the fuel tank is empty and fill it if needed. Ensure the fuel-shutoff valve is open. Verify the oil level in the crankcase and add oil if it's low. Make sure the throttle control is positioned midway between the SLOW and FAST settings. Check and replace the fuel filter if it's dirty. Inspect the air cleaner and clean or replace the element if it's dirty. Also, make sure the spark-plug wire is connected, and clean, adjust, or replace the spark plug if it's faulty. Finally, check the electrical connections for good contact, cleaning the connector terminals if necessary.
Why won't my Toro Lawn Mower starter crank?
If the starter on your Toro Lawn Mower doesn't crank, there are several things to check. First, ensure the blade-control switch (PTO) is disengaged and the parking brake is engaged. Make sure the drive levers are in the NEUTRAL-LOCK position and that you are seated on the seat. If these are all correct, check the battery to see if it's dead and charge it if necessary. Also, inspect the electrical connections for corrosion or looseness and ensure they have good contact. Finally, check the fuse and replace it if it's blown.
What to do if my Toro Lawn Mower is resulting in uneven cutting height?
If your Toro Lawn Mower is leaving an uneven cut, several factors could be the cause. Start by sharpening the blades or installing new ones if they are bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck. Adjust the tire pressure to the correct level.
How to fix a Toro 74266 when the starter does not crank?
If the starter of your Toro Lawn Mower doesn't crank, make sure the blade-control switch (PTO) is disengaged, the parking brake is engaged, the drive levers are in the NEUTRAL-LOCK position, you are in the operator’s seat, the battery is charged, the electrical connections are in good contact, the fuse is not blown (replace if necessary), and the relay or switch is functional (contact an Authorized Service Dealer if broken).
How to fix uneven cutting height on Toro 74266 Lawn Mower?
If mowing with your Toro Lawn Mower results in an uneven cutting height, sharpen the blade(s) or install new cutting blade(s) if they are bent. Level the mower deck from side-to-side and front-to-rear. Clean the underside of the mower. Adjust the tire pressure to the correct level. For issues with the blade spindle, contact an Authorized Service Dealer.
What to do if Toro Lawn Mower engine loses power?
If your Toro Lawn Mower engine loses power, try reducing the ground speed. Clean the air cleaner element and add oil to the crankcase if the oil level is low. Remove any obstructions from the cooling fins and air passages. Clean or replace the fuel cap if the vent hole is plugged. Replace the fuel filter if it's dirty.
What to do if Toro Lawn Mower blades do not rotate?
If your Toro Lawn Mower blades do not rotate, install a new deck belt. Ensure the mower deck belt is properly positioned on the pulley, checking the idler pulley, idler arm, and spring. Check the belt tension, or install a new pump drive belt. Replace the idler spring if it is broken or missing.
What to do if my Toro 74266 Lawn Mower blades do not rotate?
If the blades on your Toro Lawn Mower do not rotate, check if the mower deck belt is worn, loose, or broken, and install a new deck belt if needed. If the mower deck belt is off the pulley, reinstall it and inspect the idler pulley, idler arm, and spring for correct position and function. Also, inspect the pump drive belt for wear, looseness, or breakage; check the belt tension or install a new belt. Finally, replace the idler spring if it's broken or missing.
Why are the blades not rotating on my Toro 74266 Lawn Mower?
If the blades on your Toro Lawn Mower are not rotating, here are a few things to inspect: * Check the belt tension if the drive belt is worn, loose, or broken. * Install the drive belt and check adjusting shafts and belt guides for correct position if the drive belt is off the pulley. * Install a new deck belt if the deck belt is worn, loose, or broken. * Install the deck pulley and check the idler pulley, idler arm, and spring for correct position and function if the deck belt is off the pulley. * Replace the spring if the idler spring is broken or missing.
General| Model | 74266 |
|---|---|
| Engine Type | 4-Cycle |
| Deck Material | Steel |
| Engine | Briggs & Stratton |
| Cutting Width | 22 inches |
| Drive Type | Self Propelled |
| Fuel Capacity | 1.0 qt (0.95 L) |
| Fuel Tank Capacity | 1.0 qt (0.95 L) |
| Oil Capacity | 20 oz |
To Next Page
