Toro GrandStand 74583 User Manual

Toro GrandStand 74583

68 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

FormNo.3390-206RevA

GrandStand

®

Mower

With48in,52in,or60inTURBOFORCE

®

CuttingUnit

ModelNo.74583—SerialNo.315000001andUp

ModelNo.74588—SerialNo.315000001andUp

ModelNo.74589—SerialNo.315000001andUp

ModelNo.79589—SerialNo.315000001andUp

g017600

Registeratwww.Toro.com.

OriginalInstructions(EN)

*3390-206*A

Table of Contents

Questions and Answers:

V
valenciakennethAug 19, 2025
Why won't my Toro GrandStand 74583 engine start?
- J
  Justin AndersonAug 20, 2025
  Your Toro Lawn Mower engine might not start due to several reasons: the fuel tank could be empty or the shut-off valve closed (fill the tank and open the valve); the spark plug wire might be loose (install the wire); the spark plug could be faulty (replace it with a new, correctly gapped one); or the air cleaner might be dirty (service the air cleaner element). Also, there may be dirt in the fuel filter, which requires replacing it.
D
davissarahAug 21, 2025
How to fix Toro GrandStand 74583 that will not start?
- G
  Grace LeonardAug 22, 2025
  If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, several factors could be at play. First, ensure the fuel tank isn't empty and the shut-off valve is open; if not, replenish the fuel and open the valve. Next, check the spark plug wire to confirm it's securely connected. A faulty spark plug could also be the culprit, so inspect it for pitting or fouling and replace if necessary with a correctly gapped one. Also, a dirty air cleaner can cause this issue, so service the air cleaner element. Finally, check the fuel filter for any dirt and replace it if needed.
B
Brenda CobbAug 23, 2025
What to do if the cutting blades do not rotate on my Toro GrandStand 74583?
- A
  Amanda ParkAug 25, 2025
  If the cutting blades on your Toro Lawn Mower do not rotate, there are several potential causes. First, check the drive belt for wear, looseness, or breakage and check the belt tension. If the drive belt is off the pulley, install the drive belt and check the adjusting shafts and belt guides for correct position. If the mower deck belt is worn, loose, or broken, install a new mower deck belt. If the mower deck belt came off a pulley, install the mower deck belt and check the idler pulley, idler arm, and spring for the correct position and function. A broken or missing idler spring can also prevent blade rotation, so replace the spring.
V
veronica41Aug 26, 2025
Why does my Toro Lawn Mower engine lose power?
- C
  Corey GonzalezAug 26, 2025
  Your Toro Lawn Mower engine might be losing power because the engine load is excessive, so reduce the ground speed. The air cleaner may be dirty, so clean it. Check the oil level in the crankcase and add oil if needed. Make sure that the cooling fins and air passages above the engine are not plugged and remove any obstructions. The vent hole in the fuel cap might be plugged, so clean or replace the fuel cap. Finally, the fuel filter may be dirty, so replace it.
T
Tami NixonAug 27, 2025
How to fix an uneven cutting height on my Toro GrandStand 74583 Lawn Mower?
- R
  Robert Doyle MDAug 28, 2025
  To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening the cutting blades or installing new ones if they are bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck and adjust the tire pressure.
N
Nicole CollinsAug 29, 2025
Why is my Toro GrandStand 74583 Lawn Mower losing power?
- M
  Manuel TaylorAug 30, 2025
  If your Toro Lawn Mower engine is losing power, there are several potential causes. Make sure that the engine load isn't excessive by reducing your ground speed. A dirty air cleaner can also cause the engine to lose power, so clean the air cleaner element. Check the oil level in the crankcase and add oil if it's low. Ensure that the cooling fins and air passages above the engine are free from obstructions. The vent hole in the fuel cap may be plugged, so clean or replace the fuel cap. Finally, a dirty fuel filter can cause power loss, so replace the fuel filter.
T
Teresa FaulknerAug 31, 2025
Why is my Toro Lawn Mower producing an uneven cutting height?
- M
  Misty HoSep 1, 2025
  If your Toro Lawn Mower is producing an uneven cutting height, several factors could be the cause. Start by sharpening the cutting blades if they are not sharp. If the cutting blades are bent, replace them. Ensure the mower deck is level from side to side and front to rear. Clean the underside of the mower if it's dirty. Adjust the tire pressure to the correct level.
K
Karen PriceSep 3, 2025
What to do if the Malfunction Indicator Light (MIL) comes on in my Toro GrandStand 74583?
- S
  Stephanie FoxSep 3, 2025
  If the Malfunction Indicator Light (MIL) illuminates on your Toro Lawn Mower, it could be due to several reasons. The engine might be too hot, so turn it off and let it cool. Old gas in the tank can also trigger it, so use new gas. Ensure the fuel shut-off valve is fully open. Check the air cleaner and precleaner, clean them, or replace if necessary. Also, verify the battery is charged, and check/replace any blown fuses. Make sure a good 12 volt battery is being used and is fully charged.
J
Jeremy GarciaSep 4, 2025
How to prevent my Toro GrandStand 74583 engine from overheating?
- C
  Charles HillSep 4, 2025
  To prevent your Toro Lawn Mower engine from overheating, ensure that the engine load is not excessive by reducing the ground speed. Also, check the oil level in the crankcase and add oil if it is low. Clear any obstructions from the cooling fins and air passages above the engine.
J
Jessica EstradaSep 6, 2025
What causes abnormal vibration in my Toro Lawn Mower?
- J
  Javier PenningtonSep 7, 2025
  Abnormal vibration in your Toro Lawn Mower can be caused by several factors. The cutting blades might be bent or unbalanced, so install new ones. Check if the blade mounting bolt or the engine mounting bolts are loose and tighten them. Also, inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley.

Toro GrandStand 74583 Specifications

General

Engine Displacement	726 cc
Cutting Width	52 inches
Deck Material	7-gauge high-strength steel
Spindle Material	Cast Iron
Drive System	Hydrostatic
Speed	10 mph
Blade Tip Speed	18, 500 ft/min
Cutting Height	1.5 - 5 inches
Ground Speed (Forward)	10 mph (16.1 km/h)
Warranty	3-year limited

Related product manuals

Preview: Toro GrandStand 74589

Toro GrandStand 74589

Preview: Toro GrandStand 74534

Toro GrandStand 74534

Preview: Toro GrandStand 74574

Toro GrandStand 74574

Preview: Toro GrandStand 74558

Toro GrandStand 74558

Preview: Toro GrandStand 74549

Toro GrandStand 74549

Toro GrandStand 74578

Toro GrandStand 74550

Preview: Toro GrandStand 74504

Toro GrandStand 74504

Preview: Toro GrandStand 74567TE

Toro GrandStand 74567TE

Preview: Toro GrandStand 74534TE

Toro GrandStand 74534TE

Preview: Toro GrandStand 74504TE

Toro GrandStand 74504TE

Preview: Toro 74534TE GrandStand

Toro 74534TE GrandStand