EasyManua.ls Logo

Toro TimeCutter MX 4275T - User Manual

Toro TimeCutter MX 4275T
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FormNo.3433-820RevB
TimeCutter
®
MX4275Tand5075T
RidingMower
ModelNo.74690—SerialNo.400000000andUp
ModelNo.74694—SerialNo.400000000andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3433-820*

Table of Contents

Other manuals for Toro TimeCutter MX 4275T

Preview: Manual
Manual240 pages

Questions and Answers

  • L
    Larry BlakeSep 9, 2025
    What to do if the engine overheats on my Toro Lawn Mower?
    • E
      Erica ElliottSep 9, 2025
      If your Toro Lawn Mower engine is overheating, there could be several reasons. First, the engine load might be excessive, so try reducing the ground speed. Check the oil level in the crankcase and add oil if it's low. Make sure the cooling fins and air passages under the engine-blower housing are free from obstructions. Also, ensure the air cleaner is clean; if it's dirty, clean or replace the air-cleaner element.
  • A
    Adrian HenryAug 23, 2025
    Why does my Toro Lawn Mower engine not start, start hard, or fail to keep running?
    • J
      james61Aug 23, 2025
      Several factors can cause this issue. First, ensure the fuel tank isn't empty; if it is, fill it. If your model has a choke, make sure it's on. Check the air cleaner and replace or clean it if it's dirty. Ensure the spark plug wire(s) are securely connected to the spark plug. Inspect the spark plug(s) for pitting, fouling, or incorrect gap, and replace if necessary. Check the fuel filter for dirt and replace it if needed. Also, ensure that you have the correct fuel type in the fuel tank. Finally, verify that the oil level in the crankcase is sufficient and add oil if it's low.
  • C
    codylaraAug 25, 2025
    What to do if my Toro TimeCutter MX 4275T engine does not start?
    • E
      Eric HubbardAug 25, 2025
      If your Toro Lawn Mower engine doesn't start, starts hard, or fails to keep running, there are several possible causes. First, check if the fuel tank is empty and fill it if necessary. If your model has a choke, make sure it's on. A dirty air cleaner can also cause issues, so clean or replace it. Ensure the spark-plug wire(s) are properly connected. Inspect the spark plug(s) for damage or incorrect gap and replace if needed. Check for a dirty fuel filter and replace it. If there is dirt, water, or stale fuel in the fuel system, or if you're using incorrect fuel, contact an Authorized Service Dealer. Finally, check the oil level in the crankcase and add oil if it's low.
  • A
    Andre AdamsAug 26, 2025
    Why is my Toro TimeCutter MX 4275T Lawn Mower cutting height uneven?
    • O
      Omar MartinAug 26, 2025
      Uneven cutting height on your Toro Lawn Mower can result from several issues. The blade(s) may not be sharp, so sharpen them. If a cutting blade(s) is/are bent, install a new one. Ensure the mower is level from side-to-side and front-to-rear. If applicable, adjust the anti-scalp wheel height. Clean the underside of the mower deck if it's dirty. Adjust the tire pressure to the correct level. If a blade spindle is bent, contact an Authorized Service Dealer.
  • M
    melody07Aug 27, 2025
    What to do if my Toro TimeCutter MX 4275T starter does not crank?
    • K
      Kathleen ThompsonAug 28, 2025
      If the starter on your Toro Lawn Mower isn't cranking, there are a few things to check. Ensure the blade-control switch is disengaged and that the motion-control levers are in the PARK position. A dead battery could also be the culprit, so try charging it. Additionally, inspect the electrical connections for any corrosion or looseness, and replace the fuse if it's blown.
  • J
    jsantiagoAug 29, 2025
    How to fix a Toro TimeCutter MX 4275T engine that loses power?
    • O
      odompeterAug 29, 2025
      If your Toro Lawn Mower engine is losing power, consider these potential causes. The engine load might be too high, so reduce your ground speed. A dirty air cleaner can also cause power loss, so clean it. Check the oil level in the crankcase and add oil if necessary. Also, remove any obstructions from the cooling fins and air passages under the engine blower housing. Finally, inspect the spark plug(s) and replace if pitted, fouled, or incorrectly gapped.
  • A
    Alexa MaySep 18, 2025
    How to fix abnormal vibrations in my Toro TimeCutter MX 4275T?
    • R
      rrowlandSep 18, 2025
      Abnormal vibrations in your Toro Lawn Mower can be caused by several factors. The cutting blade(s) might be bent or unbalanced, in which case you should install new cutting blade(s). Check if the blade mounting bolt or the engine mounting bolts are loose and tighten them. Also, ensure the engine pulley, idler pulley, or blade pulley is not loose and tighten if necessary. If the engine pulley is damaged, the blade spindle is bent, or the motor mount is loose or worn, contact an Authorized Service Dealer.
  • T
    Todd PatelSep 18, 2025
    What to do if my Toro TimeCutter MX 4275T machine does not drive?
    • M
      Mrs. Janet King DVMSep 18, 2025
      If your Toro Lawn Mower isn't driving, first check if the bypass valves are open and close the tow valves. If the traction belts are worn, loose, or broken, or if the traction belts are off the pulleys, or if the transmission has failed, contact an Authorized Service Dealer.
  • C
    Carol HartSep 7, 2025
    What to do if Toro Lawn Mower blades won't spin?
    • D
      Dakota PayneSep 7, 2025
      If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken drive belt. Install a new drive belt. Also, check if the drive belt is off of the pulley, and if so, install the drive belt and check the adjusting shafts and belt guides for the correct position. Finally, check if the mower belt is worn, loose, or broken and install a new mower belt.
  • J
    James LopezSep 4, 2025
    Why is my Toro Lawn Mower engine overheating?
    • M
      Michael WoodSep 5, 2025
      If your Toro Lawn Mower engine is overheating, there are several possible reasons. First, the engine load might be excessive, so try reducing your ground speed. Second, check the oil level in the crankcase and add oil if it's low. Third, inspect the cooling fins and air passages under the engine-blower housing for any obstructions and remove them. Finally, a dirty air cleaner can cause overheating, so clean or replace it.

Toro TimeCutter MX 4275T Specifications

General IconGeneral
Cutting Width42 inches
TransmissionHydrostatic
Fuel Capacity3 gallons
SpeedUp to 7 mph
Warranty3 years
Deck MaterialSteel
Blade Tip Speed18, 500 FPM
Spindle MaterialAluminum
Cutting Height1.5 - 4.5 inches

Related product manuals