Toro Z Master Professional 6000 Series User Manual (English)

Other manuals for Toro Z Master Professional 6000 Series

Questions and Answers:

P
Pamela JamesAug 28, 2025
What to do if my Toro Z Master Professional 6000 starter does not crank?
- P
  pweeksAug 28, 2025
  If the starter on your Toro Lawn Mower doesn't crank, there are several possible reasons. First, ensure that the blade-control switch (PTO) is disengaged and the parking brake is engaged. Also, make sure the motion-control levers are in the NEUTRAL-LOCK position and that you are seated. If these aren't the issue, check if the battery is dead and charge it if necessary. Inspect the electrical connections for corrosion or looseness, and replace the fuse if it's blown. If none of these steps work, the relay or switch may be worn or damaged, and you should contact an Authorized Service Dealer.
E
ecampbellAug 27, 2025
Why won't my Toro Lawn Mower engine start, starts hard, or fails to keep running?
- T
  taylorsmithAug 27, 2025
  If your Toro Lawn Mower engine will not start, starts hard, or fails to keep running, fill the fuel tank, open the fuel shutoff valve and add oil to the crankcase. Ensure that the throttle control is midway between the “SLOW” and “FAST” positions. Also, replace the fuel filter, clean or replace the air cleaner element, check the seat switch indicator (replace the seat if needed), check the electrical connections for good contact (clean the connector terminals thoroughly with electrical contact cleaner, apply dielectric grease, and reconnect), clean, adjust, or replace the spark plug and check the spark plug wire connection. If problems persist, contact an Authorized Service Dealer.
M
Mark SerranoAug 27, 2025
Why Toro Lawn Mower blades do not rotate?
- D
  Dustin BryanAug 27, 2025
  If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken mower deck belt; in this case, install a new deck belt. Another possibility is that the mower deck belt is off the pulley; reinstall it and check the idler pulley, idler arm, and spring for correct position and function. Also, check the pump drive belt for wear, looseness, or breakage, and adjust the belt tension or install a new belt. Finally, inspect the idler spring and replace it if it's broken or missing.
N
Nicole GreerSep 3, 2025
What to do if Toro Lawn Mower produces an uneven cutting height?
- M
  Mr. Carl Clark DVMSep 3, 2025
  If your Toro Lawn Mower is producing an uneven cutting height, consider these potential causes: 1. The blades might not be sharp enough, so sharpen them. 2. The cutting blades could be bent, in which case you should install new ones. 3. The mower deck may not be level; level it from side-to-side and front-to-rear. 4. The underside of the mower might be dirty, so clean it. 5. Check and adjust the tire pressure to the correct levels. If the blade spindle is bent, contact an Authorized Service Dealer.
R
Robert VasquezSep 5, 2025
Why are the blades not rotating on my Toro Lawn Mower?
- S
  Sarah MerrittSep 5, 2025
  If the blades on your Toro Lawn Mower aren't rotating, check if the mower deck belt is worn, loose, or broken, and install a new deck belt if needed. If the mower deck belt is off the pulley, install it and check the idler pulley, idler arm, and spring for correct position and function. Verify if the pump drive belt is worn, loose, or broken; check the belt tension or install a new belt. Replace the idler spring if it is broken or missing.
A
andreachapmanSep 7, 2025
What to do if my Toro Lawn Mower machine does not drive?
- A
  Austin DavilaSep 7, 2025
  If your Toro Lawn Mower isn't driving, check these potential causes: * Ensure the bypass valves are tightly closed; tighten them if loose. * Replace the pump belt if it's worn, loose, or broken. * If the pump belt is off a pulley, change the belt. * Replace the idler spring if it's broken or missing. * Add hydraulic fluid to the reservoirs or allow it to cool down if the level is low or too hot.
W
Wendy OlsonSep 9, 2025
Why does the malfunction indicator light (MIL) come on in my Toro Z Master Professional 6000?
- S
  sanchezjennaSep 9, 2025
  The malfunction indicator light might illuminate due to several reasons: the engine overheating, old gas in the tank, a fuel shut-off valve not fully open, a dirty air cleaner, a discharged battery, incorrect or dirty fuel filters, unsecured sensor connections to the ECU and fuel injectors, low battery voltage, or a blown fuse. Try these solutions: turn off the engine to cool it, use new gas, fully open the fuel shut-off valve, clean or replace the air cleaner, charge or replace the battery, ensure a good 12 volt battery is being used and is fully charged, and check/replace any blown fuses. For issues related to fuel filters and sensor connections, it's best to contact an Authorized Service Dealer.
C
Cameron ThomasAug 26, 2025
What to do if the blades on my Toro Lawn Mower do not rotate?
- J
  jimmy47Aug 26, 2025
  If the blades on your Toro Lawn Mower do not rotate: 1. Install a new deck belt. 2. Install the mower deck pulley and check the idler pulley, idler arm, and spring for correct position and function. 3. Check the belt tension or install a new belt. 4. Replace the spring.
J
James MurilloAug 25, 2025
Why is my Toro Lawn Mower resulting in an uneven cutting height?
- K
  kyle71Aug 26, 2025
  If mowing results in an uneven cutting height with your Toro Lawn Mower, try the following: 1. Sharpen the blade(s). 2. Install new cutting blade(s). 3. Level the mower deck from side-to-side and front-to-rear. 4. Clean the underside of the mower. 5. Adjust the tire pressure.
T
Tara SimmonsAug 25, 2025
How to fix a Toro Z Master Professional 6000 when the starter does not crank?
- A
  Amanda VangAug 26, 2025
  If the starter on your Toro Lawn Mower doesn't crank, here are some things to check: 1. Move the blade control switch (PTO) to disengaged. 2. Set the parking brake. 3. Ensure that the drive levers are in the neutral lock position. 4. Sit on the seat. 5. Charge the battery. 6. Check the electrical connections for good contact. 7. Replace the fuse.