Toro Z Master Series - User Manual

FormNo.3375-555RevC
ZMaster
®
RidingMower
ForAllZMaster
®
RidingMowers
SetupInstructions
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Rearwheels(Woodencrateonly)
2
Removethemachinefromacrate.
2
Nopartsrequired
–
Addfueltothemachine.
3
Nopartsrequired
–
Checktheengine-oillevel.
4
Nopartsrequired
–
Checkthetirepressure.
5
Nopartsrequired
–
Checkthewheellugnuttorque.
6
Nopartsrequired
–
Checkthegrassdeector.
J-bolt2
Wingnut2
7
Hold-downclamp1
Installabattery(Dieselmachinesonly).
Clamp
1
Wingnut(1/4inch)
2
8
Batteryhold-down2
Installabattery(Gasolinemachines
only).
9
Nopartsrequired
–
Chargethebattery.
Seat
1
Seatplate(xedseatsonly)
1
Flangenuts(3/8inch)—xedseatsonly
8
Spacers(3/8inch)—xedseatsonly
4
Flangenuts(3/8inch)—tiltingseatsonly
4
Longspacers(tilting,deluxeseatsonly)
2
10
Shortspacers(tilting,deluxeseatsonly)
4
Installtheseat(Internationalmachines
usinggasolineonly).
11
Nopartsrequired
–
Checktheseatbelt(International
machinesusinggasolineonly).
Right-controllever1
Left-controllever
1
Bolt(3/8x1inch)—2areassembled
4
12
Nut(3/8inch)—2areassembled
4
Installthemotion-controllevers
(Internationalmachinesusinggasoline
only).
Carriagebolt(3/8x1-1/2inches)
1
13
Flangelocknut(3/8inch)
1
Installthelift-assistpedal(International
machinesusinggasolineonly).
Air-cleanercap1
14
Hoseclamp1
Installtheair-cleanercap(International
machinesusinggasolineonly).
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
*3375-555*C

Summary

Toro Riding Mower Setup Procedures

Loose Parts Verification

Verify all shipped parts are received before starting setup procedures.

Procedure 1: Removing Machine from Crate

Safely remove the riding mower from its shipping crate.

Procedure 2: Adding Fuel to the Machine

Add the correct type and amount of fuel before operating.

Procedure 3: Checking Engine-Oil Level

Verify the engine oil level is within the recommended range.

Procedure 4: Checking Tire Pressure

Ensure tires are inflated to the specified pressure.

Procedure 5: Checking Wheel Lug Nut Torque

Confirm that wheel lug nuts are tightened to the correct torque.

Procedure 6: Checking Grass Deflector

Ensure the grass deflector is correctly installed and functional.

Procedure 7: Installing Battery (Diesel Machines Only)

Install a 12V battery into diesel-powered machines.

Procedure 8: Installing Battery (Gasoline Machines Only)

Install a 12V battery into gasoline-powered machines.

Procedure 9: Charging the Battery

Charge the battery safely following all precautions.

Procedure 10: Installing Seat (International Gasoline Models)

Install the seat assembly on international gasoline models.

Procedure 11: Checking Seat Belt (International Gasoline Models)

Verify seat belt installation angle and bolt torque.

Procedure 12: Installing Motion-Control Levers (International Gasoline Models)

Install motion-control levers for international gasoline models.

Procedure 13: Installing Lift-Assist Pedal (International Gasoline Models)

Install the lift-assist pedal on international gasoline models.

Procedure 14: Installing Air-Cleaner Cap (International Gasoline Models)

Attach the air-cleaner cap to heavy-duty air cleaners.

Procedure 15: Installing ROPS Hardware (LPG Models)

Install Roll-Over Protection System hardware on LPG models.

Procedure 16: Installing ROPS (International Gasoline Models)

Install Roll-Over Protection System on international gasoline models.

Procedure 17: Installing ROPS (Diesel Models)

Install Roll-Over Protection System on diesel models.

Procedure 18: Checking Machine for Grease

Perform a visual inspection for proper machine lubrication.

Procedure 19: Removing Shipping Straps

Remove all shipping restraints before operating the machine.

Final Checks and Delivery

Procedure 20: Checking Machine Before Customer Delivery (All Models)

Perform all final checks before customer delivery.

Procedure 21: Delivering Machine to Customer (All Models)

Complete the machine delivery process and customer orientation.

Toro Z Master Series Specifications