Torso Electronics T-1 - 2.7 Clear and Copy

41
The T-1 Notebook : Reference & Guide
40
The T-1 Notebook : Reference & Guide
2.8 Command Quick Reference
Generic Setup
2
Generic Setup
2
Function Action
T-1 Sequencer Command
Description
General Play Sequence Press [PLAY] Press the play transport button to play a sequence.
General Stop Sequence Press [PLAY] Press the play transport button to stop a playing sequence.
General Play - No MIDI Hold [CTRL] + Press [PLAY] Play the pattern without sending MIDI start message.
General Exit - Home Press [BANK]
Press quickly to exit the current mode and return ‘home’. This
is the track view also the mode selected on start up.
General Secondary Option Hold [CTRL] + Button Selects the secondary function of the control, labelled in grey
General Secondary Option Hold [CTRL] + Knob Selects the secondary function of the control, labelled in grey
General Various Hold [VBx] + [VBx] Multiple selections can be made using the value buttons
General Lock display Double Press Knob
Where a visualisation on the value buttons exists, double
press the parameter knob will lock it’s value button display.
General Absolute Edit Hold (Knob) + [VBx]
Change parameter absolutely for track. Use [PATTERN] +
(Knob) + [VBx] to change across all tracks
General Relative Edit Turn (Knob)
Change parameter relatively for track. Use [PATTERN] + Turn
(Knob) to change across all tracks
Bank View Banks Hold [BANK] Value buttons will display state by their illumination colour.
Bank Select Bank Hold [BANK] + Press [VBx] Selects a bank ‘x’ - pattern selection automatically follows
Bank Save Bank Hold [CTRL] + [BANK] + [VBx] Saves the edited, selected bank ‘x’
Bank Reload Bank Hold [BANK] + [VBx] for 1 Sec Reload previously saved stave for bank ‘x’
Bank Clear Bank Hold [CLEAR] + [BANK] + [VBx] Clears bank ‘x’. [VBx] again to conrm.
Bank Copy Bank [CTRL] + [COPY] + [BANK] + [VBx]
Copy from ‘x’ source into ‘x’ destination. Keep 3 buttons held
and value button to copy and then value button to paste into.
Pattern Clear Pattern [CLEAR] + [PATTERN] + [VBx] Clears pattern ‘x’
Pattern Copy Pattern
[CTRL] + [COPY] + [PATTERN] + [VBx]
Copy from ‘x’ source into ‘x’ destination. Keep 3 buttons held
and value button to copy, then value button to paste into.
Pattern Select Pattern [PATTERN] + [VBx] Select a pattern from within the existing bank.
Pattern Chain Patterns Press [VBx] + [VBx] + etc Select, in order, the patterns to play in a chained series
Track Select Track Press [VBx] In ‘Home’ track view, to select one track.
Track Multi Track Select Press [VBx] + [VBx] + etc In ‘Home’ track view, simultaneously select multiple tracks.
Track Track Type Press [CTRL] + [VBx] Cycle between Note, CC Track and FX Track
Track Pulse View Double Tap [VBx] Switch from track view to pulse view
Track Mute / Unmute [MUTE] + [VBx]
Mute and unmute tracks. Muting takes place when the mute
button is released.
Track Quick Mute [CTRL] + [MUTE] + [VBx]
Mute and unmute tracks. Muting takes place immediately
when the buttons are pressed.
Function Action
T-1 Sequencer Command
Description
Steps View Steps Hold (STEPS) Sequencer view - display steps value button page.
Steps Edit Steps Turn (STEPS) Adjust Euclidean step count up to 16 steps.
Steps Edit Steps Press & Turn (STEPS) Adjust up to 16 step count while visualising step sequencer.
Steps Edit Steps Hold (STEPS) + Press [VBx] Adjust step count while visualising step sequencer view.
Steps Extend Steps Hold [CTRL] + Turn (STEPS)
Adjust the step count beyond 16 and up to 64 steps
distributed as 16 steps per page, max 4 pages.
Steps Step Pages Hold [CTRL] + Button
In step sequencer view. Bank, Pattern Temp, Mute buttons
represents each step page 1,2,3 and 4 respectively.
Steps Retrigger Step Press [CLEAR]
Apply a retrigger step when in step view. Rests sequence
parameters
Pulses View Pulses Hold (PULSES) Display pulses sequencer view, value button page
Pulses Edit Pules Turn (PULSES) Adjust Euclidean pulse count and population.
Pulses Edit Pulses Press & Turn (PULSES)
Adjust Euclidean pulse count while visualising pulse
sequencer view on the value buttons.
Pulses Manual Pulses Press [VBx]
Pulse sequencer view, press value buttons to select / deselect
step editable pulses. Not affected by Euclidean edits.
Pulses Rotate Hold [CTRL] + Turn (PULSES) Rotate pattern track start point.
Length Note Length Turn (SUSTAIN) Adjust note length with respect to division.
Division Edit Note Division Turn (DIVISION) Adjust the time signature division for the track pattern.
Division Edit Note Division Press & Turn (DIVISION)
Adjust the time signature division for the track pattern while
viewing the value button division status
Division Edit Note Division Hold (DIVISION) + Press [VBx]
Adjust the time signature division for the track pattern while
viewing the value button division status
Division Free Division [CTRL] + Turn (DIVISION) Change the division free form in 96 PPQN resolution
Length Reduce Length Turn (LENGTH) Reduce the sequence length
Length Random Start Press [CLEAR] Sets a random start point when playing. Glitched playback.
Length Random Start [CLEAR] + Turn (LENGTH)
Sets a random start point when playing and changing length
value. Glitched playback.
Velocity Base Velocity Turn (VELOCITY) Set the base velocity for notes
Accent Variation Velocity Turn (ACCENT) Applies the amount of groove template to the velocity prole
Groove Select Groove Turn (GROOVE)
Selects one of 8 groove templates. Also use [VBx] when
displaying groove view.
Timing Micro-timing
Turn (TIMING) Adjust the micro timing of some notes earlier or later
Delay Note delay
[CTRL] + Turn (DELAY) Adjust all notes earlier or later
Probability Chance
[CTRL] + Turn (PROBABILITY) Applies the chance of a note bing silent