Toshiba 32C110U User Manual

Chapter 5: Setting up your TV
27
Viewing the digital signal meter
You can view the digital signal meter in the ANT/
CABLE digital TV input source only.
To view the digital signal meter:
1無
Press and open the Setup menu.
2無
Highlight Installation and press .
3無
A new set of Installation menu icons will appear.
Open the Terrestrial menu, highlight Signal
Meter, and press .
4無
Press pqtu to select the antenna input and
digital channel whose signal you want to check.
Note:
•
The physical digital channel number listed in
the Signal Meter screen may not correspond
to a virtual TV channel number. Contact your
local broadcasters to obtain the RF channel
numbers for your local digital stations.
•
The signal strength does not change between
virtual channels on the same physical
channel.
To close the screen and return to the
Terrestrial menu:
Highlight Done and press .
To return to normal viewing:
Press .
Setting the time zone
The Time Zone setup will allow you to specify the
correct time zone for your region. This feature will
allow the TV status information to show the correct
time zone information ( page 49).
To set the time zone:
1無
From the Setup menu, highlight Installation and
press . A new set of Installation menu icons
will appear.
2無
Highlight Time Zone, and press .
3無
Press t or u to select the region, highlight Done,
and then press .
After the time zone has been set, you will be asked to
set the current Daylight Saving Time status.
To set the Daylight Saving Time status:
1無
Press t or u to select Yes or No, Highlight Done,
and then press .
Viewing the system status
To view the system status:
1無
Press and open the Setup menu.
2無
Highlight Installation and press .
3無
A new set of Installation menu icons will appear.
Open the System Status menu, highlight System
Information, and press .
4無
Press tu to scroll through the menu bar to select
the Factory Defaults or Support Information and
view the related information.
To close the screen and return to the
Installation menu:
Highlight Done and press .
To return to normal viewing:
Press .
Reset Factory Defaults
To reset all settings and channels to their
factory default values:
1無
Press and open the Setup menu.
2無
Highlight Installation and press . A new set of
Installation menu icons will appear.
3無
Open the System Status menu, highlight System
Information, and press .
4無
Press tu to scroll through the menu bar to select
Factory Defaults.
5無
Highlight Yes and press .
6無
(If PIN code has been set, enter your PIN code. Press
t or u to select Done and press .) A warning
message will appear, select Yes and press , the TV
will turn off automatically after a few seconds. After
the TV turns off, unplug the TV power cord and then
plug it in again to complete the reset process.
To cancel the reset:
Select No and press in step 5 above.

Toshiba 32C110U Specifications

General

Package depth	187.9 mm
Package width	876 mm
Package height	586.9 mm
Package weight	13500 g
Display diagonal	32 \
Progressive scan	Yes
Display resolution	1366 x 768 pixels
Display technology	LCD
Native aspect ratio	16:9
Native refresh rate	60 Hz
Supported video modes	720p
Supported graphics resolutions	1366 x 768
Audio formats supported	MP3
Image formats supported	JPG
SCART ports quantity	0
Card reader integrated	No
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Digital audio optical out	1
Package weight (imperial)	29.76 lbs
Weight (with stand) (imperial)	20.94 lbs
Product color	Black
LED indicators	Y, Stand-by
Panel mounting interface	200 x 100 mm
RMS rated power	14 W

Weight and Dimensions

Depth (with stand)	245 mm
Width (with stand)	792.7 mm
Height (with stand)	551.7 mm
Weight (with stand)	9500 g
Depth (without stand)	89.4 mm
Height (without stand)	503.4 mm
Weight (without stand)	8900 g