Toshiba HWT-1101XWHT6W-E Installation Manual

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

AIR TO WATER HEAT PUMP

Installation Manual

R32

English

Hydro Unit -Wall Mounted Type-

Model name:

6kW model (HWT-60)

HWT-601XWHM3W-E

HWT-601XWHM6W-E

HWT-601XWHT6W-E

11kW model (HWT-110)

HWT-1101XWHM3W-E

HWT-1101XWHM6W-E

HWT-1101XWHT6W-E

HWT-1101XWHT9W-E

14kW model (HWT-140)

HWT-1401XWHM3W-E

HWT-1401XWHM6W-E

HWT-1401XWHT6W-E

HWT-1401XWHT9W-E

Table of Contents

Other manuals for Toshiba HWT-1101XWHT6W-E

Service Manual230 pages

Questions and Answers:

L
Lee ShepardAug 9, 2025
What to do if my Toshiba HWT-1101XWHT6W-E Heat Pump room is not heated or cooled properly?
- C
  Christopher MorganAug 9, 2025
  If your Toshiba Heat Pump isn't heating or cooling the room adequately, or the water isn't hot enough, there might be several reasons: * The remote controller settings may be incorrect. Check the operation and temperature settings. * The function code setting could be wrong. Verify it using the function code table. * The backup heater might be disconnected. Inspect the backup heater and bimetal thermostat. * The unit might have insufficient capacity. Review the equipment selection. * A temperature sensor may be defective or not properly positioned. Ensure the temperature sensor is correctly installed.
C
Courtney SchneiderAug 15, 2025
What to do if nothing is displayed on the Toshiba Heat Pump remote controller?
- P
  Pamela BeltranAug 15, 2025
  If nothing is displayed on your Toshiba Heat Pump's remote controller, check the following: * Verify the power supply wiring. * Check the setting with the DN codes.
D
Diana HinesAug 21, 2025
What to do if my Toshiba Heat Pump has almost no or little water flow and shows error code [A01]?
- H
  Heather MilesAug 21, 2025
  If your Toshiba Heat Pump exhibits little to no water flow and displays error code [A01], consider the following: * There may be an air bite in the pump. Release the air completely, following the correct procedure. * The hydraulic pressure may be low. Set the hydraulic pressure appropriately, considering the pipe height, and replenish water until the manometer shows the set hydraulic pressure or more. * The strainer might be clogged. Clean the strainer. * There could be large resistance on the hydro side. Widen the water path to the Hydro Unit or adopt a bypass valve. * The motorized 3-way valve for hot water supply might be malfunctioning. Check the wiring and parts.
I
Ian LopezAug 27, 2025
Why is hot water leaking from the overpressure preventive valve of my Toshiba HWT-1101XWHT6W-E?
- S
  scarterAug 27, 2025
  Hot water leaking from the overpressure preventive valve of your Toshiba Heat Pump can be due to: * Excessive hydraulic pressure. Set the hydraulic pressure considering pipe height and replenish water until the manometer shows a value of set hydraulic pressure or more. * Insufficient capacity of the expansion tank. Check the expansion tank capacity compared to the total water amount; if it's insufficient, install another expansion tank. * Expansion tank failure. Check the air pressure.
K
Kylie BuckleySep 2, 2025
How to fix a Toshiba HWT-1101XWHT6W-E pump lock with error code [A14]?
- J
  Joseph ClarkSep 3, 2025
  If your Toshiba Heat Pump's pump is locked and displays error code [A14], it may be due to pump lock caused by dust clogging. To unlock it, insert a Phillips screwdriver into the hole and turn it to the left or right.

Toshiba HWT-1101XWHT6W-E Specifications

General

Brand	Toshiba
Model	HWT-1101XWHT6W-E
Category	Heat Pump
Language	English

Related product manuals

ESTIA R32 HWT-1101XWHT6W-E

Toshiba HWT-1101XWHT9W-E

Toshiba HWT-1101XWHM3W-E

Toshiba HWT-1101HW-E

Toshiba HWT-1101H8RW-E

Toshiba HWT-1101F21SM3W-E

Toshiba ESTIA R32 HWT-1101HW-E

ESTIA R32 HWT-1101F21MT6W-E

Toshiba HWT-1102S21SM3W-E(TR)

Toshiba HWT-1102S21ST9W-E(TR)

Toshiba HWT-1401HW-E

Toshiba HWT-1401HW-E(TR)