EasyManua.ls Logo

Toshiba HWT-1101XWHM3W-E - User Manual

Toshiba HWT-1101XWHM3W-E
230 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model name:
Outdoor unit
HWT-401HW-E(TR)
HWT-601HW-E(TR)
HWT-801HW-E(TR)
HWT-1101HW-E(TR)
HWT-801HRW-E
HWT-1101HRW-E
AIR TO WATER HEAT PUMP
Hydro unit
-Wall Mounted Type-
HWT-601XWHM3W-E(TR)
HWT-601XWHT6W-E(TR)
HWT-1101XWHM3W-E(TR)
HWT-1101XWHT6W-E(TR)
HWT-1101XWHT9W-E(TR)
Service Manual
FILE No. AE0-2101W

Table of Contents

Other manuals for Toshiba HWT-1101XWHM3W-E

Preview: Installation Manual
Installation Manual40 pages

Questions and Answers

  • M
    Mark HarrisAug 9, 2025
    What to do if my Toshiba Heat Pump room is not heated or cooled properly?
    • W
      Wayne OchoaAug 9, 2025
      If your Toshiba Heat Pump isn't heating or cooling the room adequately, or the water isn't hot enough, there might be several reasons: * The remote controller settings may be incorrect. Check the operation and temperature settings. * The function code setting could be wrong. Verify it using the function code table. * The backup heater might be disconnected. Inspect the backup heater and bimetal thermostat. * The unit might have insufficient capacity. Review the equipment selection. * A temperature sensor may be defective or not properly positioned. Ensure the temperature sensor is correctly installed.
  • B
    Benjamin HoffmanAug 15, 2025
    What to do if nothing is displayed on the Toshiba Heat Pump remote controller?
    • T
      Tracy CampbellAug 15, 2025
      If nothing is displayed on your Toshiba Heat Pump's remote controller, check the following: * Verify the power supply wiring. * Check the setting with the DN codes.
  • A
    amy21Aug 21, 2025
    What to do if my Toshiba Heat Pump has almost no or little water flow and shows error code [A01]?
    • J
      Jennifer RochaAug 21, 2025
      If your Toshiba Heat Pump exhibits little to no water flow and displays error code [A01], consider the following: * There may be an air bite in the pump. Release the air completely, following the correct procedure. * The hydraulic pressure may be low. Set the hydraulic pressure appropriately, considering the pipe height, and replenish water until the manometer shows the set hydraulic pressure or more. * The strainer might be clogged. Clean the strainer. * There could be large resistance on the hydro side. Widen the water path to the Hydro Unit or adopt a bypass valve. * The motorized 3-way valve for hot water supply might be malfunctioning. Check the wiring and parts.
  • N
    Noah SotoAug 27, 2025
    Why is hot water leaking from the overpressure preventive valve of my Toshiba Heat Pump?
    • S
      Sarah KellyAug 28, 2025
      Hot water leaking from the overpressure preventive valve of your Toshiba Heat Pump can be due to: * Excessive hydraulic pressure. Set the hydraulic pressure considering pipe height and replenish water until the manometer shows a value of set hydraulic pressure or more. * Insufficient capacity of the expansion tank. Check the expansion tank capacity compared to the total water amount; if it's insufficient, install another expansion tank. * Expansion tank failure. Check the air pressure.
  • M
    Mrs. Melissa MorganSep 2, 2025
    How to fix a Toshiba Heat Pump pump lock with error code [A14]?
    • V
      Vanessa ScottSep 2, 2025
      If your Toshiba Heat Pump's pump is locked and displays error code [A14], it may be due to pump lock caused by dust clogging. To unlock it, insert a Phillips screwdriver into the hole and turn it to the left or right.

Toshiba HWT-1101XWHM3W-E Specifications

General IconGeneral
ModelHWT-1101XWHM3W-E
CategoryHeat Pump
Cooling Capacity11000 BTU/h
Heating Capacity12000 BTU/h
SCOP4.0

Related product manuals