Reference Information
Toshiba 2-11
29
ADDITIONAL INFORMATION
Setting Control Codes
1
Press TV to set the remote control operating your TV.
2
3
Release TV.
4
Point the remote control at your TV and use each button
listed below to make sure that your TV is operated correctly.
POWER To turn the TV on or off.
CH/TRK To select TV channels in the upper or lower
direction.
VOL To adjust TV sound level.
INPUT SELECT To select an external source such as a VCR.
Number buttons To select TV channels. When selecting channels
1 to 9, first enter 0 and then the desired number.
100 To substitute for 100 channel key.
DISPLAY To turn on or off TV’s screen display.
ENTER To use for the TV’s ENTER key.
Important
Some TVs may not respond to all the operations above, or
may not be operated at all with this remote control. In this
case, operate your TV with its own remote control.
Notes
• For some brands, several control codes (brand codes) are allocated. Try
each of them until the buttons work on your TV.
• If you replace the remote control’s batteries, set the brand code again.
Multi Brand Remote Control
The remote control can be compatible with various brands of TV by setting their control codes. The
TOSHIBA code has initially been set to control TOSHIBA TVs.
ADDITIONAL INFORMATION
While holding down TV. enter the two digits of your TV’s
brand code (listed on page 30) using number buttons.
DISPLAY
ENTER
POWER
CH/TRK
VOL
100
INPUT
SELECT
Number
buttons
1,2,3
28
MTS Broadcast Compatibility
This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to
your stereo system or stereo TV, you will experience the SAP or stereo sound.
Preparation
Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.
Recording the SAP/Stereo Broadcast
1
On the SET UP screen (page 14),
select “SAP SET” using CURSOR
(
▲
) or (
▼
), and set to “ON” using
CURSOR ( ) or ( ).
2
Press PROG. twice to exit.
3
Perform a recording.
SAP (Second Audio Program broadcast):
A separate audio program, usually broadcast in a second language with the
main language.
Selecting a sound
Sounds recorded on the tape
According to your setting of “SAP SET” on the SET UP screen, the sound is recorded onto different
tracks of the tape as below. Set “SAP SET” to “ON” or “OFF” appropriately.
Hi-Fi sound track
Contents of recorded sound
On-Screen Display
(Press DISPLAY.)
Setting of “SAP SET”
on the SET UP
screen
Type of receiving
broadcast
Normal sound
track (Mono)
L
R“SAP”“STEREO”
“ON” or “OFF” not lit not lit MONO MONO MONO
“ON” or “OFF” not lit lit MONO (MIXED)
“ON” lit not lit MONO MONO SAP
“OFF” lit not lit MONO MONO MONO
“ON” lit lit MONO MONO SAP
“OFF” lit lit MONO (MIXED)
STEREO
STEREO
Regular
(monaural audio)
Stereo
Regular+SAP
Stereo+SAP
Sounds in playback
You can play SAP and/or stereo broadcasts with this VCR. Press AUDIO SELECT to select a desired
sound.
Note
When the TV is connected to the RF OUT terminal of the VCR, the output sound is monaural.
Desired sound
SAP sound
Stereo sound
L , R indicators in the VCR display
R (right) is on.
Both R (right) and L (left) are on.
Sound output
SAP
Stereo
RECORDING
EnD : PROG
SET UP
PRESET
PROGRAM
TAPE LE
n
GTH
120 160 180
SAP SET
on off
COU
n
TER MEM
on off
LA
n
GUAGE E
n
G FRA ESP
▼
▼
AUDIO
SELECT
2
1
DISPLAY
To Next Page
Loading...
