TP-Link Archer C58HP User Manual

Configure the router.
1. Connect your device to the router (wired or wireless).
Wired:
Turn off the Wi-Fi on your computer and connect it to the router via an
Ethernet cable.
Wireless:
a. Find the product label at the bottom of
the router.
b. Use the default network names (SSIDs)
and password to join the 2.4 GHz or 5
GHz network.
Tip: If you are using a smartphone or tablet,
you can also scan the QR code to join the
preset 2.4 GHz network directly.
Router Mode
1.
B. Make sure that the
adjustable elbow is
facing up when
attached.
A. Insert and screw the antenna
into the antenna socket.
2.
Slide the cap onto the antenna
until it fixes into place.
3.
Position the antenna
vertically for best Wi-Fi
performance.
Please note that the router provides three working modes:
Router, Repeater and Access Point. You can choose the
mode to better suit your network needs and follow the
guide to complete the configuration.
3. Go to Quick Setup and follow the step-by-step instructions to complete
the setup.
2. Launch a web browser, and enter http://tplinkwifi.net or
http://192.168.0.1 in the address bar. Create a password to log in.
Install the Antennas
Quick Installation Guide
High Power Wireless Dual Band Router
Note: Images may dier from actual products.
Unplug your modem, and
remove the backup battery
if it has one.
Power on the modem and
wait about 2 minutes for it
to restart.
Connect the power-off
modem to the router’s WAN
port via an Ethernet cable.
Modem
Connect the power adapter to the router and turn
on the router.
This mode enables multiple users to share internet connection via an ADSL/Cable Modem.
If your internet comes from an Ethernet outlet, connect the router’s WAN port to it, then skip Step 1, 2 and 3.
Verify that the following LEDs are solid on to
confirm the hardware is connected correctly.
WAN
ON
PWR
ON
2.4G
ON
5G
ON
3
1
2
6
5
4
Wireless Password/PIN:
XXXXXXXX
SSID:TP-Link_XXXX
SSID:TP-Link_XXXX_5G
QR
Code
Important

TP-Link Archer C58HP Specifications

General

Brand	TP-Link
Model	Archer C58HP
Category	Network Router
Language	English

Summary

Install the Antennas

Insert and Screw Antenna

Insert and screw the antenna into the antenna socket and ensure it is correctly attached.

Attach Antenna Cap

Slide the cap onto the antenna until it fixes firmly into place.

Position Antenna

Position the antenna vertically for optimal Wi-Fi performance.

Router Mode Setup

Prepare Modem and Router

Unplug modem, connect modem to router WAN port via Ethernet cable, then power on modem.

Power On Router and Verify

Connect router power adapter, turn on router, and verify LEDs are solid.

Connect Device and Configure

Connect device to router, launch browser, access http://tplinkwifi.net, and complete Quick Setup.

Repeater Mode Configuration

Configure via RE Button

Use the WPS button on the host router and the RE button on this router for connection.

Configure via Web Browser

Connect to the router, launch browser to http://tplinkwifi.net, select Repeater mode, and save.

Relocate Router

Place the router between the host router and the Wi-Fi dead zone.

Access Point Mode Configuration

Connect Router to Wired Network

Connect the router's WAN port to your wired router's Ethernet port.

Configure Router for AP Mode

Launch browser to http://tplinkwifi.net, select Access Point mode, and save.

TP-Link Tether App and Safety

TP-Link Tether App

Use the Tether app for intuitive router access and management.

Safety Information

Guidelines on keeping the device away from hazards and proper usage.

FAQ and Support

Troubleshooting Common Issues

Answers to frequent questions regarding web access, internet connectivity, and passwords.

Technical Support and Resources

Information on accessing support, user guides, community, and contacting TP-Link.