Trackunit DualID II - Introduction; Safety Information; General Safety Guidelines; Environmental and Operational Compliance

Trackunit 501 DualID
_User guide v.1.0
©Trackunit 2017
Introduction
This manual contains the functional installation guide for the DualID II product after mounting on the the
outside of the vehicles, machinery, tractor etc. The DualID II provides access control for starting the vehicles,
machinery using either an RFID identification card or a PIN code.
The DualID II operates in conjunction with the Trackunit tracking devices
ME501-
x (2G+3G) and it will also be interfaced for future tracking devices from Trackunit.
Safety information
Simple Guidelines
Please follow these guidelines when configuring, using or recycling the
may be dangerous, illegal or otherwise detrimental.
Interference
Like all wireless devices, the
DualID II
however it is unlikely as the RFID interface operates in very close range from the identification card (Approx
less than 1 cm - Typically).
Qualified Service
The DualID II
contains no user serviceable or replaceable parts. Non
an authorized service center for repair or replacement.
Water-Resistance
and environmental compliance
The DUALID II is water-
resistant according to the IP
designed to withstand the rough e
nvironmental conditions defined in the SAE J1455 Heavy Truck
environmental standard for outside mounting. The environmental compliance to SAE J1455 covers vibration
and shock, humidity and temperature, salt mist and certain chemicals etc.
It is however recommended that
the DUALID II
subjected to either water streams or
Specific Human
Absorption Rates (SAR)
The DualID II is declared
RF Exposure Compliance for Exemption from Routine
ATTESTATION: It is attested
that the radio
the routine evaluation limits in
RSS102
prepared and the information contained therei
evaluation
methodologies have been followed; and that the device meets the SAR and/or RF field
strength limits of RSS‐102.
_User guide v.1.0
This manual contains the functional installation guide for the DualID II product after mounting on the the
outside of the vehicles, machinery, tractor etc. The DualID II provides access control for starting the vehicles,
machinery using either an RFID identification card or a PIN code.
The DualID II operates in conjunction with the Trackunit tracking devices
of the models ME500
x (2G+3G) and it will also be interfaced for future tracking devices from Trackunit.
Please follow these guidelines when configuring, using or recycling the
DualID II.
Violating these guidelines
may be dangerous, illegal or otherwise detrimental.
Further detailed information is provided in this manual.
DualID II
may encounter electrical interference that
may affect its perform
however it is unlikely as the RFID interface operates in very close range from the identification card (Approx
contains no user serviceable or replaceable parts. Non
-
functioning units must
an authorized service center for repair or replacement.
and environmental compliance
resistant according to the IP
-66, IP67 and IPx9K
requirements
nvironmental conditions defined in the SAE J1455 Heavy Truck
environmental standard for outside mounting. The environmental compliance to SAE J1455 covers vibration
and shock, humidity and temperature, salt mist and certain chemicals etc.
the DUALID II
is to be mounted and
used where it is relatively dry and not
subjected to either water streams or
submersion.
Absorption Rates (SAR)
RF Exposure Compliance for Exemption from Routine
Evaluation Limits
that the radio
communication apparatus meets the exemption from
RSS102
Section 2.5 of this standard; that the Technical Brief was
prepared and the information contained therei
n is correct; that applicable measurement methods and
methodologies have been followed; and that the device meets the SAR and/or RF field
7001.0084 v1.2 23032017
This manual contains the functional installation guide for the DualID II product after mounting on the the
outside of the vehicles, machinery, tractor etc. The DualID II provides access control for starting the vehicles,
of the models ME500
-x (2G) or the
x (2G+3G) and it will also be interfaced for future tracking devices from Trackunit.
Violating these guidelines
Further detailed information is provided in this manual.
may affect its perform
ance,
however it is unlikely as the RFID interface operates in very close range from the identification card (Approx
functioning units must
be returned to
requirements
. The DualID II is
nvironmental conditions defined in the SAE J1455 Heavy Truck
environmental standard for outside mounting. The environmental compliance to SAE J1455 covers vibration
used where it is relatively dry and not
Evaluation Limits
.
communication apparatus meets the exemption from
Section 2.5 of this standard; that the Technical Brief was
n is correct; that applicable measurement methods and
methodologies have been followed; and that the device meets the SAR and/or RF field