ME500-X
Trackunit ME500-X, Technical Manual v.1.1, January 2016 Page 4
TRACKUNIT SHALL HAVE NO LIABILITY WHATSOEVER IN
CONNECTION THEREWITH. RESELLER SHALL INDEMNIFY
AND HOLD TRACKUNIT AND ITS SUPPLIERS HARMLESS
FROM ANY CLAIM BROUGHT AGAINST TRACKUNIT
WHICH ARISES FROM RESELLER’S USE OR
DISTRIBUTION OF THE PRODUCT IN CONNECTION WITH
SUCH ENVIVRONMENTS OR APPLICATIONS. SOME
STATES AND JURISDICTIONS DO NOT ALLOW
LIMITATIONS ON DURATION OR THE EXCLUSION OF AN
IMPLIED WARRANTY, SO CERTAIN OF THE ABOVE
LIMITATIONS MAY NOT APPLY TO EVERY RESELLER.
Embedded Software/Firmware
The Product and associated tools, if any, may contain embedded
software/firmware, which is licensed, not sold, and is only for
use within the Product as an integral part thereof. Such
embedded software/firmware (which includes all updates
thereto) contains valuable trade secrets and is proprietary to
Trackunit and its suppliers. To the greatest extent permitted by
law, such embedded software/firmware may not be modified,
copied, disassembled, decompiled or reverse engineered.
Trackunit reserves all other rights.
Limitation of Liability
TRACKUNIT’S ENTIRE LIABILITY REGARDING THE
PRODUCT SHALL BE LIMITED TO THE AMOUNT
ACTUALLY PAID BY RESELLER FOR THE PRODUCT. TO
THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
IN NO EVENT SHALL TRACKUNIT OR ITS SUPPLIERS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES WHATSOEVER UNDER ANY
CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANY
WAY TO THE PRODUCTS, ACCOMPANYING
DOCUMENTATION AND MATERIALS, AND ANY
EMBEDDED SOFTWARE/FIRMWARE AND UPDATES
THERETO (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, LOSS OF DATA OR ANY
OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER
TRACKUNIT HAS BEEN ADVISED OF THE POSSIBILITY OF
ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF
DEALING BETWEEN TRACKUNIT AND RESELLER.
BECAUSE SOME STATES AND JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY
FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE
ABOVE LIMITATION MAY NOT APPLY TO EVERY
RESELLER.
Notices
Class B Statement – Notice to Users. This equipment has been
tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the
receiver.
– Consult the dealer or an experienced radio/TV technician for
help.
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Regulatory Approvals
CE
The ME500-X product comply with the essential requirements
of the R&TTE Directive 1999/5/EC as stated by the EC
Declaration of Conformity (CE 0682). The ME500-X product
comply with the European Telecommunications Standards
Institute Specifications EN 301 489-1, EN 301 489-7 (EMC for
GSM 900MHz and DCS 1800MHz for Radio Equipment and
Systems).
EC/ International
The ME500-X product comply with the essential requirements
of the Automotive directive 2004/104/EC clause 6.5, 6.6, 6.8
and 6.9, UN regulative ECE R10 EMC rev4.
The ME500-X product comply with the essential requirements
of the Directive 2003/37/EEC and Directive 2006/42/EEC.
The ME500-X product comply with the international standards
ISO-13309, ISO-13766 and EN ISO-14982, for tractors, forest
and agricultural machinery, moving machinery and construction
machinery.
The ME500-X product complies with the essential and
environmental requirements of the Interoperability of trans-
European conventional rail system 2001/16/EC and 2004/50/EC
directives according to ISO 50121-3-2 and DIN EN 50125-1,
when used as intended on rolling stock and transportation.
The ME500-X complies with the essential requirements of the
2011/65/EC directive on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
FCC
The ME500-X product comply with the FCC Part 15, Part 22,
Part 24, and the Industry Canada requirements RSS-GEN, RSS-
102, RSS-132, RSS-133.
The ME500-X product comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device
must accept any interference received, including interference
that may cause undesired operation.
For fixed mounted operations the ME500-X must be installed to
provide a separation distance of at least 20 cm from all persons.
ME500-X:
FCC ID: ZMF-ME500
IC-ID: 9746A-ME500
To Next Page
Loading...
