Need help?Do you have a question about the Traxxas E REVO 56036-1 and is the answer not in the manual?
General| Scale | 1/10 |
|---|---|
| Drive Type | 4WD |
| Drive System | Shaft-Driven 4WD |
| Battery | 7-cell NiMH or 2S/3S LiPo |
| Differential Type | Sealed, oil-filled |
| Gear Pitch | 32P |
| Suspension | Independent, oil-filled shocks |
| Charger | Not included |
A step-by-step guide to getting your model operational quickly and safely.
Information on how to register your product online for better customer service.
Details on how to contact Traxxas for technical assistance and support options.
Essential guidelines for safe handling and charging of battery packs.
Specific safety procedures for Lithium Polymer battery packs.
Safety advice and limitations for the electronic speed control.
List of tools and equipment that must be purchased separately.
Suggested additional items for an R/C enthusiast's toolbox.
Instructions for applying decals for model customization.
Definitions of key terms used in radio and power system operations.
Essential precautions for maintaining radio system performance and range.
Diagram showing the electrical connections for the EVX-2 speed control.
Layout and components of the TQi transmitter and receiver.
Guide for installing AA batteries in the TQi transmitter.
Instructions for charging NiMH battery packs using the included charger.
Steps for installing battery packs into the E-Revo model.
How to adjust battery placement for optimal handling and performance.
Explanation of the Traxxas High-Current Connector's benefits.
Identification and function of the TQi transmitter controls.
How to adjust throttle neutral and steering trim for proper operation.
Procedures for operating the TQi radio system before driving.
Steps to ensure the radio system operates correctly at a distance.
Procedures for binding the transmitter and receiver.
How to adjust steering sensitivity (expo) using the Multi-Function knob.
Guidance on proper antenna installation for optimal radio reception.
How to enable/disable Low-Voltage Detection for battery protection.
How to reset transmitter settings for ESC calibration.
Step-by-step guide to calibrate the speed control to the transmitter.
How to select different operating profiles (Sport, Race, Training).
Explains the meaning of LED indicators and protection modes.
Guidelines and precautions for operating the model in wet environments.
Pre-operation checks and modifications for wet running.
Maintenance procedures after operating in wet conditions.
How to properly seal the receiver box for water resistance.
Adjusting suspension springs, sag, and ride height for optimal handling.
Details on spring rates and how to adjust ride height using push rods.
How to adjust pivot ball caps for smooth suspension movement.
How to change shock oil viscosity for damping adjustment.
Adjusting the toe angle of the front and rear wheels for handling.
Setting the static camber angle for optimal tire contact.
Guidelines for maximum toe and camber settings to avoid interference.
How to adjust the slipper clutch for tire spin control and drivetrain protection.
Information on wheel and tire selection for different terrains.
Information on motor selection, gearing, and mesh adjustment.
How to set the gear mesh for proper drivetrain operation.
How to adjust the dual-servo steering for optimal responsiveness.
Adjusting the servo saver for different servo types or performance.
Modifying steering stops to allow increased steering throw.
Checklist for inspecting the model for wear or damage.
Recommended maintenance intervals and procedures for key components.
Guidelines for proper storage of the model and batteries.
Overview of advanced suspension and alignment tuning options.
Adjusting caster angle to influence understeer/oversteer handling.
Managing bump steer by adjusting toe link positions with caster changes.
Modifying roll center to affect suspension stiffness and handling balance.
Changing rocker arms for suspension travel and rate.
Chart to eliminate bump steer based on caster and roll center settings.
Replacing shock pistons to adjust damping characteristics.
Adjusting differential fluid viscosity to control power distribution.
Guide for installing optional long travel rocker arms.
Procedures for installing motors, including brushless conversions.
Steps to reset the transmitter to its factory default settings.
Explanation of the throttle trim memory feature to prevent runaways.
Adjusting throttle sensitivity using the Multi-Function knob.
Adjusting steering throw percentage using the Multi-Function knob.
Setting servo travel limits for steering and throttle channels.
Precisely setting the neutral position for steering and throttle servos.
Managing and locking models in the transmitter's memory.
Explains the meaning of different LED indicator patterns on the transmitter.
Explains the meaning of different LED indicator patterns on the receiver.
Guide to navigating the transmitter's programming menu structure.
Quick reference for setting Multi-Function knob functions via menu tree.
Using Traxxas Link app for advanced transmitter programming and telemetry.
To Next Page