Need help?Do you have a question about the Traxxas REVO 3.3 53097-3 and is the answer not in the manual?
General| Brand | Traxxas |
|---|---|
| Model | REVO 3.3 53097-3 |
| Category | Motorized Toy Car |
| Language | English |
Contact Traxxas Technical Support for questions about your model.
Statement on compliance with FCC regulations for digital devices.
Statement on compliance with Canadian ICES-003 and RSS-210.
Statement on RF exposure limits for the equipment.
Essential safety warnings for operating the Revo model.
Precautions for handling and charging rechargeable batteries.
Lists specialty metric tools included with the Revo model.
Lists optional but recommended tools for an R/C toolbox.
Lists tools and supplies needed to operate and maintain the Revo.
Identifies the location of the TRX 3.3 Racing Engine on the model.
Identifies the EZ-Start motor and plug locations.
Introduces the Traxxas TQi 2.4GHz transmitter and its features.
Defines key terms related to the radio and power systems.
Important precautions for using the radio system safely.
Identifies controls and components of the transmitter and receiver.
Illustrates the wiring connections for the radio system components.
Step-by-step guide for installing batteries in the transmitter.
Instructions for charging the receiver battery pack.
Precautions for maintaining the rechargeable NiMH receiver pack.
Essential rules for safe and proper operation of the radio system.
Explanation of the built-in failsafe system.
Identifies and explains the controls on the transmitter.
Guides basic adjustments for throttle and steering.
Steps for checking radio system operation and basic adjustments.
Procedure for ensuring radio system range before each use.
Instructions for binding the transmitter and receiver.
Explanation of Traxxas Stability Management system.
Explanation of OptiDrive operation and status indicators.
Instructions for setting up the receiver antenna.
Step-by-step guide for programming the OptiDrive ESM.
Introduces the TRX 3.3 Racing Engine and its features.
Explains the importance and procedure for engine break-in.
Importance of air filter maintenance for engine life.
Importance of after-run maintenance for engine longevity.
Diagram showing the illustrated parts of the TRX 3.3 Racing Engine.
Defines technical terms related to the TRX 3.3 Racing Engine.
Explains adjustment of the high-speed needle for fuel mixture.
Explains adjustment of the idle speed screw for engine idle.
Describes how to lean the fuel mixture for performance.
Explains adjustment of the low-speed needle for fuel mixture.
Importance of using the correct fuel for performance and engine life.
Explains the difference and effects of nitro percentages in fuel.
Discusses the use of fuels other than Traxxas Top Fuel.
Guidelines for safely handling and storing model engine fuel.
Instructions on how to fill the Revo's fuel tank.
Importance and components of the two-stage air filter.
Steps for cleaning the air filter's pre-filter element.
Steps for cleaning the air filter's primary filter element.
Explains the functions of the carburetor and air/fuel mixture.
Details the high-speed and low-speed needles for fuel mixture control.
Recommended factory settings for carburetor needles.
How to adjust the idle speed screw for proper idle.
Overview of the EZ-Start system and its functions.
Instructions for charging the EZ-Start battery pack.
Steps for installing the EZ-Start battery into the controller.
How to use the EZ-Start controller to start the engine.
Explanation of the EZ-Start protection mode.
Importance of using a fully charged battery for the EZ-Start.
Detailed instructions for breaking in the TRX 3.3 Racing Engine.
Step-by-step procedure for the initial break-in tanks.
Procedures for starting the engine for the first time.
Procedures for fuel tanks 1-5 during engine break-in.
Instruction to clean air filter after break-in before proceeding.
Tips for performing engine break-in in cold weather conditions.
Importance of fuel mixture for engine tuning and performance.
Procedure for adjusting the high-speed fuel mixture.
Procedure for adjusting the low-speed fuel mixture using the pinch test.
Chart showing how weather affects fuel mixture adjustments.
How to adjust idle speed after mixture tuning.
General advice on fine-tuning the carburetor based on conditions.
How engine temperature can be used as a tuning aid.
General introduction to driving the Revo.
Advice and techniques for driving the Revo model.
Adjusting springs and ride height for optimal suspension performance.
How to adjust spring pre-load and select appropriate springs.
Adjusting ride height using push rods and suspension arms.
Adjusting pivot ball caps for free operation.
How shock oil viscosity affects suspension damping.
Step-by-step guide for replacing shock oil.
Critical alignment settings for optimizing Revo performance.
How to adjust toe-in and toe-out settings.
Adjusting static camber for optimal handling.
Suggested maximum alignment settings for different configurations.
Adjusting transmission components for performance.
How to adjust the slipper clutch for traction and protection.
Adjusting the transmission's shift point for acceleration.
Setting the correct gear mesh between spur and clutch bell gears.
Procedure for replacing the spur gear.
Importance of dual servo alignment for steering performance.
Steps for adjusting steering links and servo saver.
Brake adjustment procedures and pad wear.
How to increase steering system throw for maximum travel.
Procedures to perform after every hour of operation.
Procedures to perform after each driving session.
Periodic maintenance tasks for the engine and clutch.
Detailed steps for performing after-run maintenance.
Procedure to clear a flooded engine.
Procedure to release a piston stuck at top dead center.
Advanced suspension and alignment adjustments.
How to adjust caster angle for handling characteristics.
Adjusting caster and bump steer for stability.
Adjusting roll center to affect suspension stiffness and traction.
Changing rocker arms to alter suspension rate and travel.
Chart for eliminating bump steer based on caster and roll center.
Explains shock piston hole sizes and their effect on damping.
Steps for disassembling shocks to change pistons.
Steps for reassembling shocks after piston replacement.
Tuning transmission and differential for performance.
Chart showing available gear ratio combinations.
How to tune differentials using silicone fluid viscosity.
Instructions for installing optional Long Travel rocker arms.
Introduction to the Traxxas Link App for model tuning.
Ease of use of the Traxxas Link App interface.
Using Traxxas Link for real-time data display and logging.
How Traxxas Link manages multiple models and settings.
Overview of adjustments accessible via mobile device or transmitter.
Adjusting steering sensitivity (exponential) via the Multi-Function knob.
Explains the meaning of transmitter LED indicator codes.
Explains the meaning of receiver LED indicator codes.
How decreasing steering sensitivity affects control.
Adjusting steering throw percentage (Dual Rate).
Adjusting throttle sensitivity (exponential) via the Multi-Function knob.
Setting servo travel limits (end points) for steering and throttle.
Explanation of the Traxxas Link Model Memory feature.
How to activate Model Lock to prevent deletion.
Steps to activate Model Lock on a memory entry.
Steps to delete a model from memory.
Guide to navigating the TQi transmitter's menu tree.
To Next Page