How to reset my TRENDnet TEW-655BR3G Wireless Router to default settings?
To reset your TRENDnet 150Mbps Mobile Wireless N Router to its default settings: 1. Ensure the router is powered on. 2. Locate the Reset button on the right side. 3. Press and hold the Reset button for 8 seconds, then release. 4. After the router reboots, it will be back to the factory default settings.
What to do if my TRENDnet Wireless Router wireless client can't access the Internet?
If your wireless client cannot access the internet using the TRENDnet Wireless Router, first ensure the router is close enough to your client, as you might be out of range. Then, verify that the SSID and encryption key are correct. Also, make sure your client is connected to the correct access point. If these steps don't work, you can reset the router to its default settings.
What to do if my TRENDnet Wireless Router Ethernet connection is not working?
If your TRENDnet Wireless Router's ethernet connection isn't working correctly, first ensure the RJ45 cable is securely connected to the router. Next, verify that your Network Interface Card adapter setting is enabled. If the settings are correct, confirm you're not using a crossover Ethernet cable, as not all Network Interface Cards are MDI/MDIX compatible; a patch cable is recommended. If the connection still fails, you can reset the router to its default settings.
Why does my TRENDnet Wireless Router wireless connection keep dropping?
If your TRENDnet Wireless Router wireless connection keeps dropping, consider the antenna orientation. Try changing the channel on the router, your access point, and your wireless adapter to a different channel to avoid interference. Also, keep the router away from electrical devices that generate RF noise, such as microwaves, monitors, and electric motors.
What to do if I forgot my TRENDnet TEW-655BR3G encryption key?
If you forgot your encryption key for the TRENDnet WiFi Mobile Router, go back to the advanced settings to set up your encryption key again. Alternatively, reset the router to its default settings.
Why can’t I configure my TRENDnet TEW-655BR3G Wireless Router even though the cable is plugged in?
If you can't configure your TRENDnet Wireless Router even when the cable is plugged in and the LED is lit, perform a Ping test to ensure the router is working properly and responding. Also, ensure that your Ethernet adapter is working and all network drivers are installed correctly.
What to do if my TRENDnet TEW-655BR3G can’t recognize my 3G data card?
If your TRENDnet Wireless Router can’t recognize your 3G data card even when it is plugged in, check the latest compatibility list to see if your 3G card is supported.
What to do if my TRENDnet Wireless Router 3G connection fails by auto detection?
If your TRENDnet Wireless Router 3G connection fails by auto detection, select “Manual” mode and manually enter the dial-up settings.
What to do if my TRENDnet Wireless Router 3G connection failed even when the dongle is plugged in?
If your TRENDnet Wireless Router 3G connection is failing even when the dongle is plugged in: 1. Make sure you have inserted a validated SIM card in the 3G data card, and the subscription from ISP is still available. 2. If you activate PIN code check feature in SIM card, making sure the PIN code you fill in dial-up page is correct. 3. Check with your ISP to see all dial-up settings are correct. 4. Make sure 3G signal from your ISP is available in your environment.
What to do if my country and ISP are not on the TRENDnet TEW-655BR3G list?
If your country and ISP are not listed on the TRENDnet Wireless Router, choose “Others” from the list and manually enter the dial-up settings.
Step-by-step guide to physically install and connect the router for initial use.
Guides users through the initial software configuration using the setup wizard.
Provides instructions for upgrading the router's firmware.
Allows backing up and restoring the device's configuration settings.
Resets the router to its original factory default settings.
Solves issues with configuring the router when connected via Ethernet.
Addresses common issues related to 3G connectivity and setup.
Helps resolve problems with setting up or maintaining wireless connections.
General| Wireless Standard | IEEE 802.11n |
|---|---|
| Wireless Speed | Up to 300Mbps |
| Frequency Band | 2.4 GHz |
| Number of Antennas | 2 |
| Antenna Gain | 5 dBi |
| Ports | 4 x 10/100 Mbps LAN ports |
| WAN Port | 1 x 10/100 Mbps WAN port |
| Security | WEP, WPA, WPA2 |
To Next Page
