Trimble R10 User Manual

TrimbleR10ReceiverWebHelp
 Loggingrate
 Positionrate
 Elevationmask
Theseparametersarealwaysresettothefactorydefaultvalueswhenthereceiverisswitchedoff.
PowerUpapplicationfile
Thepowerupapplicationfile(Power_up.cfg)isusedtosetthereceivertoaspecificconfiguration
anytimetheunitispoweredup.
Inthisfile,youcanspecifythatthereceiverisresettodefaultsbeforethepowerupsettingsare
applied.Thisensuresthatrestartingthereceiveralwaysresets
ittofactorydefaultsbeforeapplying
thepowerupapplicationfile.
Alternatively,youcanspecifythatthepowerupsettingsareappliedimmediatelyafterthecurrent
applicationfile’ssettingshavebeenapplied.Restartingthereceiverresultsinaconfigurationthat
usesyourdefaultsettingsfortheoptionsyoudefinein
thepowerupfile,butthecurrentsettings
forallotheroptions.
Bydefault,thereisnopower_upapplicationfileonthereceiver.Touseapowerupapplicationfile,
youmustcreateandsaveapower_upapplicationfileintheGPSConfiguratorsoftware.Ifyousave
thisfileto disk,
thefileiscalledpower_up.cfg.Theextension.cfgisused,byconvention,toidentify
applicationfilesontheofficecomputer.Whenyoutransferthisfiletothereceiver,thefileissaved
onthereceiveraspower_up,andbecomesthenewpowerupfile.
Applyingapplicationfiles
Anapplicationfile’s
settingsdonotaffectthereceiver’sconfigurationuntilyouapplythe
applicationfile.Youcandothisatthesametimethatyousavethefile.Alternatively,youcansave
thefileonthecomputeroronthereceiver,thenopenitlaterandapplyitssettings.
Storingapplicationfiles
You
canstoreapplicationfilesthatyoucreateintheGPSConfiguratorsoftwareonthereceiverand
onthecomputer.Forexample,eachfilecanrepresentadifferentusersharingthesamereceiver,
oraparticularmodeofoperation.Savingapplicationfilesonyourcomputeraswellasinyour
receiver
isoptional,butitisusefulbecause:
 itgivesyouapermanentcopyofthesettingsyouhavesenttoareceiver,forauditpurposesor
foryourownreference.
 youcanusethesamefiletoconfiguremultiplereceiversidentically.
 youcanuseanexistingapplicationfile
asatemplatetocreateotherapplicationfileswith
similarsettings.
Namingapplicationfiles
Theapplicationfilenameintheofficecomputerandinthereceiverarealwaysthesame.This
makesiteasiertorecognizeandkeeptrackofyourapplicationfiles.
Whenyouchangethenameoftheapplication
fileinthereceiver,thischangestheapplication
filenameonyourcomputer.Whenyoutransferanapplicationfilefromthereceiverandsaveitto

Trimble R10 Specifications

General

Channels	440
RTK Horizontal Accuracy	8 mm + 1 ppm RMS
RTK Vertical Accuracy	15 mm + 1 ppm RMS
Operating Temperature	-40 °C to +65 °C
L1 C/A Code	Yes
L2E	Yes
L2C	Yes
L5	Yes
Beacon	No
FM Radio	No
WAAS	Yes
MSAS	Yes
EGNOS	Yes
Storage Temperature	-40 °C to +75 °C
Ingress Protection	IP67
Positioning Accuracy (Static) - Horizontal	3 mm + 0.5 ppm RMS
Positioning Accuracy (Static) - Vertical	5 mm + 0.5 ppm RMS
Signal Tracking	BeiDou
RTK Initialization	< 8 seconds
Battery Life	Up to 7 hours
SBAS Accuracy	50 cm
Glonass Code	L1 C/A, L2 C/A
Communications	Bluetooth