What to do if red “LOAD” light is flashing on Tripp Lite Battery Charger?
If the red “LOAD” operation indicator light is flashing on your Tripp Lite Battery Charger, the inverter is likely overloaded. Reduce the load. To reset the unit, move the Operating Mode Switch to “DC OFF,” wait 1 minute, and then switch to “AUTO/REMOTE” or “CHARGE ONLY.”
Why is the red “LOW” battery light flashing on my Tripp Lite Battery Charger?
If the red “LOW” battery indicator light is flashing on your Tripp Lite Battery Charger with the Operating Mode Switch in the “AUTO/REMOTE” position, it could be due to low battery voltage, causing the unit to shut down to protect the battery. If AC power is present, the unit will automatically reset and start recharging. If you're using an external charger, manually reset the unit by moving the Operating Mode Switch to “DC OFF” for two seconds, then back to “AUTO/REMOTE.” Another cause might be a false reading from undersized or poorly connected DC cabling. Ensure you're using DC cable of sufficient size that is sufficiently connected to the Inverter/Charger.
Why is my Tripp Lite Battery Charger not recharging?
If your Tripp Lite Battery Charger isn't recharging with AC input present, the connected batteries might be dead, so check and replace them if necessary. Also, the battery fuse might be blown, so inspect and replace it if needed. Lastly, make sure the battery cabling is securely connected; check and tighten or replace the cabling if it's loose.
What does it mean when all three “BATT VOLT/ CHRG CURR” LEDs are rapidly flashing on Tripp Lite Battery Charger?
If all three “BATT VOLT/ CHRG CURR” LEDs are rapidly flashing on your Tripp Lite Battery Charger while in “AUTO/ REMOTE” mode, the battery is likely overcharged, causing the unit to shut down to prevent damage. This may be due to connected auxiliary chargers or the unit’s charger. Disconnect any auxiliary chargers. Reset the unit by moving the Operating Mode Switch to “DC OFF,” wait 1 minute, and then switch back to “AUTO/REMOTE.”
What does it mean when all three “BATT VOLT/ CHRG CURR” LEDs are slowly flashing on Tripp Lite Battery Charger?
If all three “BATT VOLT/ CHRG CURR” LEDs are slowly flashing on your Tripp Lite Battery Charger with the Operating Mode Switch in the “AUTO/ REMOTE” position, the battery is excessively discharged. The unit will shut down to prevent battery damage. Use an auxiliary charger to raise the battery voltage. Check external battery connections and the fuse. The unit will automatically reset when the condition is cleared.
What to do if Tripp Lite Battery Charger has no AC output?
If your Tripp Lite Battery Charger has no AC output and all indicator lights are off, first ensure the unit is properly connected to utility power. If it is, check that the Operating Mode Switch is not set to “OFF” while AC input is present; if it is, switch it to “AUTO/REMOTE” or “CHARGE ONLY.” Also, check the output circuit breaker and reset it if it's tripped. The unit might have shut down due to battery overcharge or excessive battery discharge or overload. In the case of overcharge, disconnect any auxiliary chargers and reset the unit by moving the Operating Mode Switch to “DC OFF,” waiting 1 minute, and then switching to “AUTO/REMOTE” or “CHARGE ONLY.” For excessive battery discharge, use an auxiliary charger to raise the battery voltage and check external battery connections and the...
Crucial safety precautions and warnings for installation, operation, and storage.
Guidance on choosing appropriate deep cycle battery types.
How to determine required battery amp-hour capacity for your application.
Guidelines for connecting DC wiring, including cable gauge and length.
Instructions for properly connecting the DC fuse and fuse block.
Detailed steps for hardwiring AC input and output connections.
General| Efficiency | 90 % |
|---|---|
| Output power | 2400 W |
| Input voltage | 24 V |
| Output voltage | 120 V |
| Input frequency | 60 Hz |
| Country of origin | China |
| Product color | Black |
| Dimensions (WxDxH) | 215.9 x 412.8 x 184.2 mm |
| Package depth | 543.6 mm |
| Package width | 375.9 mm |
| Package height | 327.7 mm |
| Package weight | 19960 g |
| Harmonized System (HS) code | 8504.40.9570 |
| Quantity per master (outer) case | 1 pc(s) |
Weight and Dimensions| Depth | 412.8 mm |
|---|---|
| Width | 215.9 mm |
| Height | 184.2 mm |
| Weight | 17690 g |
To Next Page