7
Cutting Tool Safety
WARNING. Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as
that specified on the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in serious injury to the user,
and damage to the tool. If in doubt, do not plug in the tool. Using a power
source with a voltage less than the nameplate rating is harmful to the motor.
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a tool is
suitable without checking the product literature before use
Protect your eyes
• Always wear appropriate eye protection when using cutting tools
• Spectacles are not designed to offer any protection when using this
product; normal lenses are not impact resistant and could shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 85dB
Protect your breathing
• Ensure that yourself, and others around you, wear suitable dust masks
Protect your hands
• Do not allow hands to get close to the cutting wheel or blades. Use a
suitable push stick for shorter workpieces with appropriate power tools
Be aware of others around you
• It is the responsibility of the user to ensure that other people in the vicinity
of the work area are not exposed to dangerous noise or dust and are also
provided with suitable protective equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded objects
before cutting
• Do not attempt to cut material that contains embedded objects unless you
know that the cutting tool fitted to your machine is suitable for the job
• Walls may conceal wiring and piping, car body panels may conceal fuel
lines, and long grass may conceal stones and glass. Always check the
work area thoroughly before proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed from the
cutting tool. It is the user’s responsibility to ensure that other people in the
work area are protected from the possibility of projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check that
wrenches / adjusters are removed prior to use
• Only use cutting tools recommended for your machine
• Do not attempt to modify cutting tools
• Ensure blades are sharp, in good condition and correctly fitted
• Do not attempt to resharpen blades. Hardened blades or blades made
from hardened alloys typically containing tungsten cannot be resharpened
without professional equipment.
• Only fit blades specifically designed and intended for this tool
• In the event blades encounter an embedded object in use that the blades
are not suitable for, blades should be replaced immediately
Direction of feed
• Always feed work into the blade or cutter against the direction of
movement of the blade or cutter
Beware of heat
• Cutting tools and workpieces may become hot in use. Do not attempt to
change tools until they have been allowed to cool completely
Control dust / swarf
• Do not allow dust or swarf to build up. Sawdust is a fire hazard, and some
metal swarf is explosive
• Be especially careful when cutting wood and metal. Sparks from metal
cutting are a common cause of wood dust fires
• Where possible, use a dust extraction system to ensure a safer working
environment
Additional Cutting Tool Safety for US
1. WEAR CORRECT APPAREL. Do not wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry which may get caught in moving parts.
Non-slip footwear is recommended. Wear protective hair covering to
contain long hair.
2. ALWAYS USE SAFETY GLASSES. Also use a face or dust mask if the cutting
operation is dusty. Everyday eyeglasses only have impact-resistant lenses;
they are NOT safety glasses.
3. SECURE WORK. Use clamps or a vise to hold work when practical. It is
safer than using hands and also it frees both hands to operate tool.
4. DON’T OVERREACH. Keep proper footing and balance at all times.
5. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating and changing
accessories.
6. DISCONNECT TOOLS before servicing, and when changing accessories,
such as blades, bits, cutters etc.
7. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in
‘OFF’ position before plugging in.
8. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for
recommended accessories. The use of incorrect accessories may create a
risk of injury to persons.
9. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if
the cutting tool is unintentionally contacted.
10. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced.
11. DIRECTION OF FEED. Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
12. NEVER LEAVE THE TOOL RUNNING UNATTENDED. SWITCH THE POWER OFF.
Do not leave the tool unattended until it comes to a complete stop.
Planer Thicknesser Safety for US
• If the replacement of the supply cord is necessary, this has to be done
by the manufacturer or his agent in order to avoid a safety hazard.
• It is strongly recommended that the tool always be supplied via a
residual current device with a rated residual current of 30 mA or less.
• This appliance is not intended for use by person (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.
636949_Manual.indd 7 28/02/2019 12:15
To Next Page
Loading...
Need help?
General
