eelio
Assembly
Please
carefully
follow
the
steps
in
this
Section
to
properly
assemble
your
new
machine.
These
steps
will
not
take
very
long
and
they
will
assure
you
of
having
assem-
bled
your
machine
correctly.
WARNING
To
prevent personal injury
or
property
damage,
do
not
start
the
engine
until
all
assembly
steps
are
complete
and
you
have
read
and
understand
the
safety
and
operating instructions
in
this
Manual.
Subjects covered in this Section:
• Inspection After Delivery
:
~:~:~k::::
~::d~:::::ng
Contents
~
• Remove Tiller from Shipping
Platform
I}
• Connect
Forward
Intl!tlock
Wire
Harness
• Attach WheelslTineslPTO Drive Leve
• Check
Gear
Oi Levels in
Power
Unitt
and
Tine Attachment Tral1smissions
t
rL
• Add
Motor
Oil to ·Iler Engin
.J'!~,'.
"-.
~/v
j
• Attach Engine Throttle
Leverto
Handlebar
• Adjust the
Air
Pressur
·n the Tires "
• Assembling the Electric
Start
System
Tools
Needed:
One
3/8"
Open
End
or
Adjustable
Wrench
One
9/16"
Open
End
or
Adjustable
Wrench
One
3/4"
Open
End
or
Adjustable
Wrench
Two
7/16"
Open
End
or
Adjustable
Wrenches
Two
1/2"
Open
End
or
Adjustable
Wrenches
One
Flat
Blade
Screwdriver
Scissors
(to
trim
plastic
ties)
Quality
Motor
Oil
(refer
to
the
Engine
Owner
Manual
provided
with
your
unit
for
motor
oil
specifica-
tions
and
capacities).
Tire
Pressure
Gauge
A
strong
4
1
12"
high
prop
(a
wood
box,
a
brick,
or
boards)
I
Inspection
After
Delivery
Inspect your machine immediately
after it has been delivered. Make
sure that neither the carton nor the
contents have been damaged.
If
you find or suspect any damage,
contact the carrier (trucking com-
pany) right away. Inform them
of
the specific damage and that you
wish to file a claim.
To
protect
your rights, be sure
to
put this
in
writing
to
the carrier within
15
days after your machine arrives.
The carrier will let you know how
to proceed with your claim.
Please let us know
if
you need any
assistance with this matter.
IMPORTANT:
Motor
oil
must
be
added
to the engine before it
is
started.
The
procedure for
adding oil is explained
later
on
in these assembly instructions.
9
STEP
1:
Unpacking
Contents
If
you haven't done so, unpack
and check the loose parts as listed
in
the table on page
10.
Contact
us
if
any parts are missing.
A. Remove the handlebars and
the WheelslTineslPTO Drive
Lever (Items 1 and 2 in Photo
2-1).
You
may need to cut a plas-
tic tie to free the handlebars from
its shipping location. Set them on
a clean surface. Do not get dirt on
the wire harness plug located at
the bottom
of
the handlebars!
B. Remove the loose parts from
the plastic envelope that contained
these instructions (Items 3 through
8 in Photo 2-2).
C.
If
you ordered an Electric Start
Tiller, take out the items from a
sealed plastic hardware package
under the battery clamp (Items 9
through
11
in Photo 2-3). Your ig-
nition keys are in the keyswitch.
To Next Page
