Troy-Bilt TB15CS User Manual (English)

Questions and Answers:

L
Laura LiuJul 30, 2025
Why Troy-Bilt TB15CS Trimmer engine will not start?
- C
  Christopher OdonnellJul 30, 2025
  If your Troy-Bilt Trimmer engine won't start, there are several potential causes: * The On/Off Stop Control might be in the OFF position. If so, turn it to ON. * The fuel tank may be empty. Refill it with properly mixed fuel. * The primer bulb may not have been pressed enough. Press it fully and slowly 10 times. * The engine could be flooded. Squeeze the trigger and pull the starter rope. * The fuel may be old or improperly mixed. Drain the gas tank and add a fresh fuel mixture. * The spark plug might be fouled. Replace or clean it. * The spark arrestor could be plugged. Clean or replace it. * The EZ-Start lever might not be set/flipped. Flip the EZ-Start lever.
S
scott84Aug 3, 2025
How to fix Troy-Bilt Trimmer engine that will not idle?
- J
  Jared IngramAug 3, 2025
  If your Troy-Bilt Trimmer engine won't idle, it might be due to: * A plugged air filter. Replace or clean the air filter. * Old or improperly mixed fuel. Drain the gas tank and add fresh fuel mixture. * Improper carburetor adjustment. Adjust according to the Carburetor Adjustments section.
K
Kimberly CruzAug 8, 2025
Why is the cutting line advancing uncontrollably on my Troy-Bilt Trimmer?
- N
  Nicholas DeanAug 9, 2025
  If the cutting line on your Troy-Bilt Trimmer advances uncontrollably, it could be due to oil, cleaner, or lubricant in the cutting head. Clean and thoroughly dry the cutting head to resolve this issue.
S
sara87Aug 14, 2025
What to do if Troy-Bilt Trimmer engine will not accelerate?
- L
  Luis MorrowAug 14, 2025
  If your Troy-Bilt Trimmer engine won't accelerate, consider these potential causes: * Old or improperly mixed fuel could be the issue. Drain the gas tank and add a fresh fuel mixture. * The carburetor might need adjustment. Take it to an authorized service dealer for adjustment. * The cutting attachment might be bound with grass. Stop the engine and clean the cutting attachment. * A dirty air filter can cause acceleration problems. Clean or replace the air filter. * A plugged spark arrestor can also be the culprit. Clean or replace the spark arrestor.
J
Jessica MillerAug 18, 2025
Why does my Troy-Bilt TB15CS Trimmer engine lack power or stall?
- J
  Joseph BushAug 18, 2025
  If your Troy-Bilt Trimmer engine lacks power or stalls, consider the following: * Old or improperly mixed fuel could be the cause. Drain the gas tank and add a fresh fuel mixture. * The carburetor may need adjustment. Take it to an authorized service dealer for carburetor adjustment. * A fouled spark plug can lead to power loss. Replace or clean the spark plug. * A plugged spark arrestor might be the problem. Clean or replace the spark arrestor.
A
Angela OdonnellAug 25, 2025
What to do if the cutting attachment will not advance on Troy-Bilt Trimmer?
- B
  Benjamin LittleAug 25, 2025
  If the cutting attachment on your Troy-Bilt Trimmer won't advance, check these: * The cutting attachment may be bound with grass. Stop the engine and clean the cutting attachment. * The cutting attachment might be out of line. Refill with new line. * The inner reel could be bound up. Replace the inner reel. * The cutting head might be dirty. Clean the inner reel and outer spool. * The line could be welded. Disassemble, remove the welded section, and rewind. * The line may be twisted when refilled. Disassemble and rewind the line. * Not enough line might be exposed. Push the bump knob and pull out the line until 4 inches (102 mm) of line is outside of the cutting attachment.

Troy-Bilt TB15CS Specifications

General

Engine Type	2-Cycle
Engine Displacement	25 cc
Start Type	Recoil
Handle Type	Loop
Attachment Capable	Yes
Shaft Type	Straight
Line Diameter	0.095 in.

Summary

INTRODUCTION

SERVICE INFORMATION

Describes service and dealer locations.

PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONS

Mentions changes and copyright.

SPARK ARRESTOR NOTE

Important safety note for specific regions.

CALIFORNIA PROPOSITION 65 WARNING

Health warning about chemicals.

RULES FOR SAFE OPERATION

SAFETY SYMBOLS EXPLANATION

Explains safety symbols and their meaning.

IMPORTANT SAFETY INSTRUCTIONS

General safety rules before operating the unit.

SAFETY WARNINGS FOR GAS UNITS

Specific warnings for gasoline-powered units.

SAFE FUELING AND MIXING

Instructions for handling fuel safely.

WHILE OPERATING

Guidelines for operating the trimmer safely.

OTHER SAFETY WARNINGS

Additional safety precautions.

SAFETY AND INTERNATIONAL SYMBOLS

Explains various symbols used in the manual.

KNOW YOUR UNIT

APPLICATIONS

Lists uses for the trimmer.

UNIT DIAGRAM

Identifies main parts of the trimmer.

ASSEMBLY INSTRUCTIONS

INSTALL AND ADJUST THE D-HANDLE

Steps to attach and adjust the handle.

INSTALL THE CUTTING ATTACHMENT SHIELD

Steps to install the cutting attachment shield.

OIL AND FUEL INFORMATION

OIL AND FUEL MIXING INSTRUCTIONS

Details on fuel/oil ratios and types.

USING BLENDED FUELS

Precautions for using blended fuels.

USING FUEL ADDITIVES

Recommendations for fuel additives.

STARTING/STOPPING INSTRUCTIONS

STARTING INSTRUCTIONS

Step-by-step guide to start the engine.

STOPPING INSTRUCTIONS

Steps to safely turn off the unit.

OPERATING INSTRUCTIONS

OPERATING THE EZ-LINK™™ SYSTEM

How to use optional attachments.

REMOVING THE CUTTING ATTACHMENT OR ADD-ONS

Procedure for detaching parts.

INSTALLING THE CUTTING ATTACHMENT OR ADD-ONS

Procedure for attaching parts.

HOLDING THE TRIMMER

Proper posture and grip for operation.

ADJUSTING TRIMMING LINE LENGTH

How to extend the trimmer line.

TIPS FOR BEST TRIMMING RESULTS

Advice for efficient cutting.

DECORATIVE TRIMMING

Technique for detailed trimming.

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE

Table of required maintenance frequencies.

LINE INSTALLATION

Covers line replacement methods.

WINDING THE EXISTING INNER REEL

Steps to rewind the trimmer line.

SINGLE LINE INSTALLATION

Specifics for single line setup.

SPLITLINE™™ INSTALLATION

Specifics for SplitLine™™ setup.

INSTALLING A PREWOUND REEL

Steps for installing a pre-wound spool.

AIR FILTER MAINTENANCE

Steps for removing, cleaning, and reinstalling the air filter.

SPARK ARRESTOR MAINTENANCE

How to clean and maintain the spark arrestor.

CARBURETOR ADJUSTMENT

Information on carburetor adjustments.

REPLACING THE SPARK PLUG

Steps to replace the spark plug.

TRANSPORTING

Instructions for safely moving the unit.

CLEANING

How to clean the unit.

STORAGE

Guidance for storing the unit.

LONG TERM STORAGE

Specific procedures for extended storage.

TROUBLESHOOTING

ENGINE WILL NOT START

Common causes and solutions for starting issues.

ENGINE WILL NOT IDLE

Common causes and solutions for idling issues.

ENGINE WILL NOT ACCELERATE

Common causes and solutions for acceleration issues.

ENGINE LACKS POWER OR STALLS WHEN CUTTING

Common causes and solutions for power loss.

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

Common causes and solutions for line feed issues.

CUTTING LINE ADVANCES UNCONTROLLABLY

Common causes and solutions for uncontrolled line advance.

SPECIFICATIONS

ENGINE*

Technical specifications for the engine.

DRIVE SHAFT and CUTTING ATTACHMENT*

Technical specifications for the drive shaft and cutting attachment.

EPA Emission Control Warranty Statement

Your Warranty Rights and Obligations

Explains owner's responsibilities for emissions warranty.

Owners Warranty Responsibilities

Details owner's duties for warranty.

Manufacturer's Warranty Coverage

Outlines what the manufacturer covers and for how long.

MANUFACTURER'S LIMITED WARRANTY

HOW TO OBTAIN SERVICE

Instructions on getting service.

WARRANTY EXCLUSIONS

Lists items not covered by warranty.

STATE LAW AND WARRANTY

Explains legal rights related to warranty.

Related product manuals